Key takeaways
- Five drill press vises for woodworking, from a compact 3 inch flat vise to a 6 inch cross slide, with jaw, travel and mounting specs for every pick.
What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Buying Guides › Best Drill Press Vises: Flat and Cross Slide Picks
A drill press vise does one job that no hand clamp does well: it holds stock flat, square and still while the bit comes down, and it keeps your fingers well away from the spinning chuck. In a woodworking shop that means dowel holes that land on the layout line, shelf pin holes in clean rows, and small parts held firmly enough to bore without the piece grabbing and spinning. The right vise also bolts to the table, so repeat work runs faster because the workholding stays put between pieces.
The five vises below split into two flat vises for simple one-hole-at-a-time work and three cross slide vises that move the work on two axes without unclamping. Jaw widths run from 3 inches to 6 inches, and the group covers budget, mid-range and premium tiers. Each pick lists the jaw, travel and mounting figures its maker publishes, so you can match the vise to your press table and the size of stock you drill most often.
As an Amazon Associate, we earn from qualifying purchases.
Contents
Quick answer
For most woodworking drill presses, the Shop Fox D4082 is the sweet spot: a 4 inch cross slide vise that moves work on two axes without unclamping. Choose the WEN DPA423 or Yost LDPV-4 for simple flat work on a budget, and the Wilton CS4 or CS6 for heavier, repeatable hole patterns.
The best drill press vises
Flat vises clamp and hold in one position, which suits single holes and short runs. Cross slide vises add two cranked slides under the jaws, so a row of holes becomes a matter of dialing the work along rather than loosening, shifting and clamping again.
WEN Drill Press Vise, 3-Inch (DPA423)
The WEN DPA423 is the compact budget pick for benchtop presses and small stock. Its 3 inch jaws open 3.1 inches with a 1 inch throat depth, which covers doweling, hardware boring and the small blocks that make up most drill press work in a furniture shop. The cast iron body gives it enough mass to sit steady, and four onboard mounting slots let you bolt it to the table in the orientation your table slots allow. The jaw inserts reverse: one face is smooth for finished wood surfaces, the other is textured for a firmer bite on rough stock. Two bolts, nuts and washers come in the box for mounting. It is a light duty tool, but for a small press that mostly bores wood it does the holding job without drama.
Specs
– Model: DPA423
– Jaw width: 3 in
– Jaw opening: 3.1 in
– Throat depth: 1 in
– Material: Cast iron
– Mounting: Four onboard slots
– Jaw inserts: Reversible, smooth and textured faces
– Weight: Not stated
Yost Tools LDPV-4 Light Duty Drill Press Vise
The Yost LDPV-4 stretches the budget format to a full 4 inch jaw while staying light enough to lift on and off the table between jobs. At 5.7 pounds it is the lightest vise in this group, and the slotted base makes positioning simple: drop it on the table, line the slots up with the table slots, and bolt it down. The textured 4 inch jaw faces grip stock firmly, and the shallow 0.85 inch throat depth keeps the whole unit low, which preserves room under the chuck on short benchtop presses. That shallow throat is the trade-off to note, since tall workpieces sit high in the jaws. For drilling flat stock, small boxes and hardware, it is a sensible light duty choice that leaves the rest of the tool budget for bits and jigs.
Specs
– Model: LDPV-4
– Jaw width: 4 in
– Jaw opening: Not stated
– Throat depth: 0.85 in
– Material: Cast iron
– Base: Slotted mounting base
– Jaw faces: Textured
– Weight: 5.7 lb
Shop Fox D4082 4-Inch Cross-Sliding Vise
The Shop Fox D4082 is the mid-range step into cross slide work. Both slides travel 4 inches, so a line of shelf pin holes or a grid of dowel holes becomes a sequence of crank turns instead of repeated unclamping. A slide bar under the moving jaw keeps it from tilting up or sideways as you tighten, a detail many vises in this tier leave out, and adjustable gibs on both slides take up slack as the vise wears in. The 4 inch jaws open 3-3/4 inches, and at 5-1/4 inches tall overall it sits lower than the Wilton cross slides below, which matters on a benchtop press with limited daylight between chuck and table. It weighs about 22 pounds, heavy enough to feel planted once bolted down. Woodstock backs it with a one year warranty.
Specs
– Model: D4082
– Jaw width: 4 in
– Jaw opening: 3-3/4 in
– Slide travel: 4 in on the top slide, 4 in on the bottom slide
– Overall height: 5-1/4 in
– Weight: 22 lb
– Features: Anti-tilt slide bar, adjustable gibs on both slides
– Warranty: 1 year
Wilton CS4 Cross Slide Drill Press Vise (11694)
The Wilton CS4 is the premium 4 inch cross slide in this group, built from fine grain cast iron with hardened steel jaw faces grooved in a V pattern, so round stock such as dowels and pen blanks can be held upright or on their side. Travel runs 4-9/10 inches on each axis, the longest in this size class here, and the cast side knobs dial movement in 0.1 mm increments for careful hole spacing. The base bolts down through five lugs, and the jaw insert assembly is a replaceable part, so worn jaw faces can be swapped without replacing the vise. At 5-3/4 inches tall and 20 pounds it suits mid-size benchtop and floor presses with the daylight to spare. Wilton covers it with a limited lifetime warranty for the original owner.
Specs
– Model: CS4, stock number 11694
– Jaw width: 4 in
– Jaw opening: 4 in
– Jaw depth: 1-3/8 in
– Slide travel: 4-9/10 in on each axis
– Overall height: 5-3/4 in
– Weight: 20 lb
– Jaws: Hardened steel, V-grooved, replaceable inserts
– Mounting: Five bolt lugs
– Warranty: Limited lifetime
Wilton CS6 Cross Slide Drill Press Vise (11696)
The CS6 is the big floor press option, a 59 pound cross slide vise with 6 inch jaws that open the full 6 inches and a 2 inch jaw depth for tall stock. Travel is 7.9 inches on each axis, enough to walk a wide cabinet part through a full row of holes without resetting the clamping. The body is cast iron with hardened steel jaw faces, again V-grooved for round work, and the base mounts through five bolt lugs. Its listed footprint is 9.5 by 14 inches with a 7.25 inch height, so it needs a full-size table and a press with generous daylight; on a small benchtop machine it would crowd out the work. For a floor press that drills large panels and batch parts, it is the heavy-duty end of this lineup, backed by a lifetime warranty against manufacturing defects.
Specs
– Model: CS6, stock number 11696
– Jaw width: 6 in
– Jaw opening: 6 in
– Jaw depth: 2 in
– Slide travel: 7.9 in on each axis
– Dimensions: 9.5 x 14 x 7.25 in
– Weight: 59 lb
– Jaws: Hardened steel, V-grooved, replaceable inserts
– Mounting: Five bolt lugs
– Warranty: Lifetime against manufacturing defects
How to choose
Begin with jaw width and opening. The jaw width should match or exceed the width of the stock you drill most, and the opening needs to swallow the thickest piece you plan to clamp, with the understanding that a workpiece held near the top of deep jaws stays more secure than one pinched at the jaw tips. Throat or jaw depth matters for tall parts: a shallow vise holds flat stock well but lets tall pieces rock.
Decide next whether you need slides. A flat vise is simpler, lower and lighter, and it is the right call for single holes and short runs. A cross slide earns its height and weight when you drill rows, grids or mirrored patterns, because the cranks move the clamped work in small, repeatable steps. Check the travel figures against the longest row you drill, and check overall height against the daylight between your chuck and table with your longest bit fitted.
Finally, look at mounting and jaw faces. The vise base slots or lugs have to line up with your table slots, and bolt size should match your table hardware. Textured or serrated faces bite hard and can mark soft wood, so smooth or reversible inserts suit finished surfaces, while V-grooves earn their keep if you bore dowels, spindles or other round stock held upright.
Who should skip
Skip a drill press vise entirely if your press work is mostly large flat panels that a fence and hold-down clamps already handle well, since a vise adds height and setup time without adding control on big sheet goods. Skip the cross slide models if you only ever drill one hole per part; the slides add play that careful gib adjustment manages but never removes, and a flat vise holds with less fuss. Skip the two Wilton models if your benchtop press has limited daylight, because their height plus a long bit can leave no room for the workpiece. And skip every vise here for milling: these are drilling vises, and side loads from milling cutters are outside what their slides and jaws are built to take.
Frequently asked questions
Can a drill press vise hold round stock such as dowels?
Yes, with the right jaw shape. V-grooved jaw faces, like those on the two Wilton cross slides above, cradle round stock held upright or on its side. In a flat vise with plain faces, a shop-made V-block under the work does the same job.
Does a cross slide vise turn a drill press into a milling machine?
No. The slides are built for positioning work between drilled holes, not for side loads from a milling cutter. Use a cross slide to step from hole to hole while the spindle is stopped, and keep milling work on a machine built for it.
How do I mount a vise to a drill press table?
Line the slots or lugs in the vise base up with the slots in the table, then bolt through with hardware that matches your table, using at least two bolts set diagonally and four for the steadiest hold. Snug the vise down, check the fixed jaw runs parallel to your fence line, and then clamp the first piece.
What size vise fits a benchtop drill press?
Match the vise footprint to the table and leave daylight for the work plus the bit. Compact flat vises in the 3 to 4 inch class, such as the WEN DPA423 and Yost LDPV-4, suit most benchtop tables, while tall cross slides need a taller press or shorter bits to keep enough working room.
Final verdict
For most woodworking shops the Shop Fox D4082 hits the balance: real two-axis movement, a slide bar that keeps the jaw honest, and a height that still fits many benchtop presses. The WEN DPA423 and Yost LDPV-4 cover simple flat holding on a budget, the Yost adding a wider jaw and the WEN reversible inserts. Step up to the Wilton CS4 for finer dial control and replaceable hardened jaws, and to the CS6 when a floor press and wide parts justify a 59 pound vise. Bolt the pick down firmly, and the press will reward you with holes that land where the pencil line says.
Product and ASIN Reference
| Product | ASIN |
|---|---|
| WEN Drill Press Vise, 3-Inch (DPA423) | B09Q4PG9GB |
| Yost Tools LDPV-4 Light Duty Drill Press Vise | B07C1MC28S |
| Shop Fox D4082 4-Inch Cross-Sliding Vise | B005W16WT0 |
| Wilton CS4 Cross Slide Drill Press Vise (11694) | B009E0E9YK |
| Wilton CS6 Cross Slide Drill Press Vise (11696) | B009E0EA3A |
Related guides
Read next
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.





Write Your Review
No reviews yet. Be the first to share your experience!