Updated Nov 20, 2026· 9 min read

Key takeaways

  • Compare the best diamond sharpening plates for plane irons and chisels, with grit, plate size, surface type and fluid guidance for every pick.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

⭐ Key Takeaways
Quick answer: Our top pick is DMT D8C Dia-Sharp Bench Stone, Coarse, with DMT D8F Dia-Sharp Bench Stone, Fine as a strong alternative.

A dull plane iron tears grain instead of slicing it, and a rounded chisel bevel wanders off the line. Diamond plates fix both problems without the soaking, dishing and flattening routine of water stones. They stay flat, cut every steel used in modern edge tools, and work with a splash of water or completely dry.

As an Amazon Associate, we earn from qualifying purchases.

The catch is that plates are not interchangeable. Grit ratings, surface patterns and base construction differ between brands, and the right plate for regrinding a nicked bevel is the wrong one for final honing. This guide compares five well-regarded plates, with the exact grit, size and surface variant each listing covers.

This article contains affiliate links, and we may earn a commission when you buy through them at no extra cost to you.

Contents
  1. Quick Answer
  2. SHARPAL 162N Double-Sided Diamond Sharpening Stone
  3. DMT D8C Dia-Sharp Bench Stone, Coarse
  4. DMT D8F Dia-Sharp Bench Stone, Fine
  5. SHARPAL 168H Dual-Grit Diamond Sharpening Stone
  6. DMT DuoSharp Plus Bench Stone, Extra Fine/Fine, with Base
  7. How to Choose
  8. Who Should Skip
  9. FAQ
  10. Final Verdict

Quick Answer

For most woodworkers, the SHARPAL 162N is the best single purchase: its coarse 325 face flattens chisel backs and regrinds bevels, the extra fine 1200 face hones a working edge, and the storage case doubles as a non-slip bench base. If you mainly need heavy stock removal, the single-grit DMT D8C coarse plate is the faster, tougher specialist.

SHARPAL 162N Double-Sided Diamond Sharpening Stone

The 162N pairs the two grits a woodworker reaches for most often on one 8 x 3 inch plate: a coarse side at 325 grit (45 micron) for restoring dull or damaged edges, and an extra fine side at 1200 grit (9 micron) for honing. That spread covers the classic plane-iron routine — flatten the back and set the primary bevel on the coarse face, then refine on the fine face before a strop.

SHARPAL describes the abrasive as monocrystalline diamond, the harder-wearing crystal form, bonded to a flat steel plate. The surface is continuous rather than perforated, which matters for narrow chisels and plane iron tips because there are no holes to catch an edge mid-stroke. The plate ships in a storage case with a non-slip pad that doubles as the bench base, plus an angle guide. SHARPAL markets it for dry or water use and promotes the coarse side for flattening water stones — the most complete one-plate package in the group.

Specs:
– Plate size: 8 x 3 in
– Grits: 325 (45 micron) coarse / 1200 (9 micron) extra fine, double-sided
– Diamond type: monocrystalline, per SHARPAL
– Surface/base: continuous surface on steel plate; storage case with non-slip base and angle guide included
– Fluid guidance: dry or water, per SHARPAL
– Flattening use: coarse side marketed for flattening water stones

View the SHARPAL 162N on Amazon

DMT D8C Dia-Sharp Bench Stone, Coarse

DMT D8C Dia-Sharp Bench Stone, Coarse (325)

DMT D8C Dia-Sharp Bench Stone, Coarse (325)

Check price on Amazon

The D8C is the plate many shops buy purely for grunt work: a single-sided 8 x 3 inch steel plate with a continuous coarse surface rated at 325 mesh (45 micron). DMT positions it for restoring neglected edges, and woodworkers lean on it for flattening chisel backs and grinding out nicks before finer abrasives take over.

DMT specifies micronized monocrystalline diamond for the Dia-Sharp line, on a steel plate 0.38 inches thick with non-slip feet. Because the surface is continuous, a wide plane iron can be worked across the whole face without the edge dropping into perforations, keeping backs flat rather than striped. DMT’s guidance is water or dry, never oil. One limitation: DMT sells a separate Dia-Flat line for dedicated stone lapping and does not designate Dia-Sharp plates as lapping plates, so treat this as a tool-sharpening plate first.

Specs:
– Plate size: 8 x 3 x 0.38 in
– Grit: 325 mesh (45 micron) coarse, single-sided
– Diamond type: micronized monocrystalline, per DMT
– Surface/base: continuous surface on steel plate, non-slip feet
– Fluid guidance: water or dry; DMT advises against oil
– Flattening use: not a designated lapping plate (Dia-Flat is DMT’s lapping line)

View the DMT D8C on Amazon

DMT D8F Dia-Sharp Bench Stone, Fine

DMT D8F Dia-Sharp Bench Stone, Fine (600)

DMT D8F Dia-Sharp Bench Stone, Fine (600)

Check price on Amazon

The D8F is the fine-grit sibling of the D8C, built on the same 8 x 3 inch continuous-surface steel plate but rated at 600 mesh (25 micron). That grade is the everyday maintenance grit for edge tools: it refreshes a slightly dull plane iron, raises a burr on a chisel bevel, and cleans up the scratch pattern left by a coarse plate so final honing goes quickly.

DMT specifies micronized monocrystalline diamond and a continuous surface, which suits wide irons and long chisel backs better than interrupted patterns, and non-slip feet keep the plate planted. Fluid guidance matches the line: water or dry, no oil. On its own the D8F will not rescue a chipped edge in reasonable time, so pair it with a coarse plate such as the D8C.

Specs:
– Plate size: 8 x 3 x 0.38 in
– Grit: 600 mesh (25 micron) fine, single-sided
– Diamond type: micronized monocrystalline, per DMT
– Surface/base: continuous surface on steel plate, non-slip feet
– Fluid guidance: water or dry; DMT advises against oil
– Flattening use: not a designated lapping plate

View the DMT D8F on Amazon

SHARPAL 168H Dual-Grit Diamond Sharpening Stone

The 168H is SHARPAL’s alternative two-grit combination: 325 grit (45 micron) coarse on one face and 1000 grit (15 micron) extra fine on the other, on an 8 x 3 inch plate. The 1000-grit side sits between the 600 and 1200 grades elsewhere in this guide, leaving a keener edge than a 600 plate while cutting fast enough for routine honing.

SHARPAL describes the abrasive as monocrystalline diamond, triple electroplated onto a steel base, and publishes a flatness figure under its MirrorFlat name: precision ground to within 0.002 inches (0.05 mm) — the quality flat backs depend on. Instead of a storage case, the 168H comes with a non-slip pad and a four-angle guide marked at 14, 17, 20 and 25 degrees, aimed more at knife users than honing-guide woodworkers. SHARPAL states it works dry or with water and needs no lapping; heavy stone flattening is best left to the coarse side.

Specs:
– Plate size: 8 x 3 in (203 x 76 mm)
– Grits: 325 (45 micron) coarse / 1000 (15 micron) extra fine, double-sided
– Diamond type: monocrystalline, triple electroplated, per SHARPAL
– Surface/base: continuous surface on steel base; non-slip pad and 4-angle guide included
– Fluid guidance: dry or with water, per SHARPAL
– Stated flatness: within 0.002 in (0.05 mm)

View the SHARPAL 168H on Amazon

DMT DuoSharp Plus Bench Stone, Extra Fine/Fine, with Base

DMT DuoSharp Plus Bench Stone, Extra Fine/Fine, with Base (WM8EF-WB)

DMT DuoSharp Plus Bench Stone, Extra Fine/Fine, with Base (WM8EF-WB)

Check price on Amazon

The DuoSharp Plus takes a different approach: its faces use DMT’s interrupted dot pattern, where the abrasive sits in a field of recessed dots that give swarf somewhere to go. The plate measures 8 inches long, with the diamond area at 6 x 2.63 inches per side, and this WM8EF-WB variant is double-sided — fine 600 mesh (25 micron) on one face, extra fine 1200 mesh (9 micron) on the other — a honing and polishing plate rather than a grinder.

DMT specifies micronized monocrystalline diamond here as well. The interrupted surface is a matter of preference: the dots clear debris well, but a narrow chisel or a plane iron’s corner can catch on the pattern if you press hard, so light, flat strokes matter. This listing bundles the bench stone base, holding the plate at a comfortable height. DMT guidance is water or dry, no oil. Because both faces are fine grades, pair it with a coarse plate for repairs.

Specs:
– Plate size: 8 in overall; diamond surface 6 x 2.63 in per side
– Grits: 600 mesh (25 micron) fine / 1200 mesh (9 micron) extra fine, double-sided
– Diamond type: micronized monocrystalline, per DMT
– Surface/base: interrupted dot-pattern surface; bench stone base included
– Fluid guidance: water or dry; DMT advises against oil
– Flattening use: not a designated lapping plate

View the DMT DuoSharp Plus on Amazon

How to Choose

Start with the jobs you actually do. Regrinding nicked bevels and flattening backs calls for a coarse plate around 325 mesh; routine maintenance sits at 600; final honing lands between 1000 and 1200. A double-sided plate like the SHARPAL 162N or 168H covers two steps in one purchase, while single-grit plates like the D8C and D8F let you upgrade one stage at a time.

Surface pattern is the second decision. Continuous surfaces, as on the Dia-Sharp plates and both SHARPAL models, are safer for wide plane irons and flat backs because nothing interrupts the stroke. Interrupted dot surfaces, as on the DuoSharp Plus, clear swarf quickly and suit narrow edges, but demand a lighter touch. Size matters too: an 8 x 3 inch plate gives a 2-inch plane iron room to travel. Check what the listing includes — a case or base, as bundled with the 162N and DuoSharp Plus, saves buying a holder. Finally, follow each maker’s fluid guidance: DMT says water or dry, no oil; SHARPAL rates its plates for dry or water use.

Who Should Skip

Skip diamond plates entirely if your edges only need a light refresh and you already own fine water stones you enjoy using. Skip the fine-only plates, the D8F and the DuoSharp Plus, if your tools arrive with chips and rounded bevels, because removing damage at 600 grit and up takes a very long time. Skip the coarse D8C as your only plate, since 325 mesh leaves scratches too deep for clean end-grain work without finer steps after it. And if your main goal is flattening water stones weekly, buy a dedicated lapping plate instead: DMT points buyers to its Dia-Flat line for that job.

FAQ

Can I flatten water stones with these plates?

Some makers say yes and some say no. SHARPAL promotes the coarse sides of the 162N and 168H for flattening water stones. DMT does not designate its Dia-Sharp or DuoSharp plates as lapping plates and sells the Dia-Flat line for that purpose, so follow your brand’s guidance.

Should I use water, oil or nothing on a diamond plate?

Follow the maker. DMT advises water or dry use and warns against oil, which can gum up the diamond surface. SHARPAL rates the 162N and 168H for dry or water use. Either way, wipe the plate clean after a session so swarf does not scratch the next tool.

Which grit do I need for plane irons and chisels?

Use around 325 mesh to flatten backs and repair damage, 600 mesh for everyday sharpening and burr raising, and 1000 to 1200 mesh to refine the edge before stropping. Most benches need only a coarse plate plus one fine plate, or a double-sided plate pairing those ranges.

Do diamond plates wear out?

The steel stays flat for years, but the diamond layer slowly loses bite, especially if you lean hard on coarse plates. Light pressure lets the diamonds cut instead of tearing them from the bond, and cleaning the surface keeps it cutting near its original speed.

Final Verdict

For a single purchase that grinds and hones, the SHARPAL 162N earns the top spot with its 325/1200 pairing, continuous monocrystalline surface and case that works as a bench base. Woodworkers building a dedicated station should pair the DMT D8C with the D8F for an all-continuous setup, while the SHARPAL 168H suits anyone wanting a 1000-grit finishing face and a published flatness figure. The DMT DuoSharp Plus is the comfortable finishing station for tools already in good shape. Match the grit sequence to your edges, follow the maker’s fluid guidance, and your tools will come off the bench ready to cut.

F
FD Woodworking Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Diamond Sharpening Plates for Plane Irons and…Check price on Amazon

Related guides

Browse all Uncategorized guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.