Key takeaways
- Compare five speed squares on size, aluminum or polymer bodies, laser-etched, stamped and molded markings, rafter scales and saw guide edges for shop work.
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Best Speed Squares for Layout, Roofing and Shop Marking
- Top Pick: Swanson Tool S0101 7-Inch Speed Square
- Runner-up: Empire Level e2994 TRUE BLUE 7-Inch Rafter Square
- Also consider: Johnson Level 1959-0700 Magnetic Johnny Square, 7-Inch
A speed square is a triangular layout tool that folds the jobs of a try square, a mitre square, a protractor, a line scriber and a saw guide into one small triangle that rides in a tool belt. Every model looks roughly the same at a glance, so the real differences hide in the details: whether the body is cast aluminum or molded polymer, whether the graduations are laser etched, stamped or molded in, and which rafter scales the maker prints on the face. Those details decide how quickly you can lay out a rafter and how steadily the tool sits against a board as a fence for a circular saw.
As an Amazon Associate, we earn from qualifying purchases.
This guide compares five current speed squares using only the specifications their makers publish: size and body material, marking method, the scales each square carries for common, hip and valley work, and saw-guide setup. Where a maker does not publish a figure, the specification is listed as not stated.
This article contains affiliate links, so the site may earn a commission if you buy through them, at no extra cost to you.
Quick Answer
If you buy one speed square, make it the Swanson S0101. The original 7-inch aluminum square pairs 1/8-inch and 1/16-inch graduations with the Blue Book rafter reference, and it covers common and hip-valley layout plus saw-guide duty. The Empire e2994 runs it close with laser-etched markings, while the Swanson Speedlite suits siding work.
The Five Squares Compared
Swanson Tool S0101 7-Inch Speed Square
The S0101 is the original Speed Square, the design Albert Swanson developed in 1925, and it is still the reference point for the category. Swanson lists the body as high-grade solid aluminum in the familiar blue finish, at a published weight of 8 ounces. The face carries graduations in both 1/8-inch and 1/16-inch increments, a fine scale for shop marking and a coarser one for framing layout. Swanson describes the tool as five tools in one: a try square, a mitre square, a saw guide, a line scriber and a protractor. The scales cover common rafter layout and hip-valley work, read against the pivot point at the corner of the triangle. Every S0101 ships with Swanson’s Blue Book, the pocket rafter reference built around the company’s One Number Method, which walks through common, hip and valley cuts with a single rise figure.
Specs
- Size: 7 inches
- Material: high-grade solid aluminum, as Swanson lists it
- Markings: graduations in 1/8-inch and 1/16-inch increments; application method not stated
- Scales: common rafter and hip-valley rafter scales, plus a protractor degree scale
- Saw guide: yes, listed by Swanson as one of the tool’s five functions
- Weight: 8 ounces
- Included: Blue Book rafter reference
See the Swanson S0101 on Amazon
Empire Level e2994 TRUE BLUE 7-Inch Rafter Square
Empire builds the e2994 from extruded 6063 aluminum with an anodized matte finish, and its headline feature is the marking method: the graduations are laser etched and filled for high visibility, and Empire states that the laser-etched markings are permanent and will not fade with heavy use. The face carries the standard rafter scales alongside conversion tables for common applications, so rise-to-angle lookups happen on the tool instead of on paper. Empire’s SCRIBE-GUIDE feature is a pattern of scribe notches spaced for marking parallel lines at 1/4-inch and 1/2-inch increments along a board, which speeds up repetitive rip layout. The heel is wider than the one on earlier Empire squares, a change the maker says adds stability when the square is used as a cutting guide on wide material such as deck boards. Empire also etches a code on the square that links to an online rafter book. The pitch is readability: high-contrast etched figures on a body that will not rust or corrode.
Specs
- Size: 7 inches
- Material: 6063 aluminum, anodized matte finish
- Markings: laser etched, high visibility
- Scales: common rafter scale and degree scale, with conversion tables for common applications printed on the tool
- Scribe feature: SCRIBE-GUIDE notches for marking at 1/4-inch and 1/2-inch increments
- Saw guide: yes, with a widened heel for stability as Empire describes it
- Weight: 7 ounces, as listed for the model
See the Empire e2994 on Amazon
Johnson Level 1959-0700 Magnetic Johnny Square, 7-Inch
Johnson’s Johnny Square line was designed around a carpenter’s complaint: standard rafter squares mark crosscuts well but handle rip layout poorly. The 1959-0700 answers with continuous scribing grooves running from 1 inch through 5-1/2 inches, so a pencil rides in a groove and draws a parallel line down a board. The body is aluminum with the line’s Easy-Read laser-etched graduations, and Johnson fits this model with a magnetic heel that holds the square to steel studs, beams and other ferrous stock while you mark. Johnson describes the family as having solid aluminum construction with CNC-machined edges for accuracy, under a low-glare finish. The scales cover common rafter cuts and hip-valley layout. This is the pick for mixed shop and site work where the square keeps meeting steel framing, and for anyone who marks a lot of rip lines.
Specs
- Size: 7 inches
- Material: aluminum
- Markings: laser etched, Easy-Read graduations
- Scales: common rafter and hip-valley rafter scales, plus a degree scale
- Scribe feature: continuous scribing grooves from 1 inch through 5-1/2 inches
- Special feature: magnetic heel for holding on ferrous material
- Weight: not stated
See the Johnson 1959-0700 on Amazon
IRWIN Tools 1794464 Rafter Square, 7-Inch
The IRWIN 1794464 keeps the formula simple: a rust-proof aluminum body, deep permanent markings, and a layout of functions that mirrors the classic pattern. IRWIN describes the square as working as a protractor, a saw guide, and a tri and mitre square, which covers the daily layout jobs in a small shop: checking a corner, marking a 45-degree mitre, reading an angle, and fencing a circular saw for a straight crosscut. The deep markings are the durability story here: the graduations are cut into the body rather than printed on it, so they stay readable after the face has been dragged across lumber and sheet goods. IRWIN does not publish a breakdown of every scale or a weight for this model, so those entries are not stated below.
Specs
- Size: 7 inches
- Material: aluminum, rust-proof as IRWIN describes it
- Markings: deep, permanent markings
- Scales: rafter layout scales with a protractor function; full scale list not stated
- Saw guide: yes, listed among the tool’s functions by IRWIN
- Weight: not stated
- Model number: 1794464
See the IRWIN 1794464 on Amazon
Swanson Tool T0701 Speedlite 12-Inch Composite Square
The Speedlite is the polymer entry in this group, and the big one: a 12-inch square molded from high-impact polystyrene that Swanson describes as a lightweight structural foam plastic. Swanson positions the orange composite body at siding work, because the plastic will not scratch or mar finished surfaces the way a metal edge can, and the 12-inch legs span wide boards a 7-inch square cannot register against in one placement. Swanson says the Speedlite offers the essential features of its aluminum Big 12 Speed Square in composite form, so the layout pattern and rafter scales follow the company’s established 12-inch design. The trade-offs are the ones polymer always brings: the body is light and kind to finished material, but a molded edge is not the fence you would choose for daily circular-saw guiding, and Swanson does not publish a weight or a marking method for this model.
Specs
- Size: 12 inches
- Material: high-impact polystyrene, described by Swanson as structural foam plastic
- Markings: not stated
- Scales: Big 12 layout pattern with rafter scales; detailed scale list not stated
- Color: orange
- Weight: not stated
- Saw guide: not stated
See the Swanson T0701 Speedlite on Amazon
How to Choose
Start with size. A 7-inch square covers studs, joists and most shop stock, rides in a belt, and is the default for framing and woodworking layout. Move to a 12-inch square when the work is wide: siding, stair stringers and large panels that a shorter leg cannot span in one placement. Next, pick the body material. Aluminum squares register flat, survive drops, and give you a metal edge to run a saw against. A polymer body such as the Speedlite is lighter and will not mar finished surfaces, but it gives up the hard fence edge.
Then read the markings. Laser-etched graduations, as on the Empire and the Johnson, are cut into the surface and filled for contrast, and both makers sell them on permanence and readability. Deep cut markings, as IRWIN describes, follow the same logic. Molded graduations are part of the body itself on polymer squares. Finally, match the scales to the work: common and hip-valley scales plus a protractor arc cover roof layout, conversion tables save lookups, scribe grooves speed up rip marking, and a magnetic heel earns its place only if you regularly mark steel.
Who Should Skip
Skip this category entirely if your layout work is fine joinery. A speed square is a framing and general layout tool, and its scales are not a substitute for a machinist square when you are fitting drawers and doors. Skip the polymer Speedlite if the square’s main job will be guiding a circular saw; a molded body is not built to be a daily saw fence. Skip the magnetic Johnson if you work almost entirely in timber and sheet goods, since the magnet adds nothing there. And skip every square here if you work in metric: these five are inch tools, with graduations and rafter tables built around inches and roof pitch.
FAQ
Is a speed square the same thing as a rafter square?
Yes, the names describe the same triangular tool. Speed Square began as Swanson’s product name for its 7-inch square, and rafter square describes what the scales are for: laying out rafter cuts.
Which size is better, 7 inch or 12 inch?
The 7-inch size is the general-purpose choice and fits a tool belt. The 12-inch size earns its place on wide material, stairs and siding, where its longer legs register in a single placement. Many roofers carry both.
Do laser-etched markings last longer than printed ones?
Etching cuts the graduation into the body rather than printing it on the surface, and makers such as Empire state that their laser-etched markings are permanent and will not fade with heavy use. An etched or deeply cut scale remains readable as long as the body does.
Can a speed square really guide a circular saw?
Yes. Hook the heel over the edge of the board, hold the square firmly, and run the saw’s shoe along its straight edge. A thick heel and a flat metal body make the guide steadier, which is why the aluminum squares here list saw guiding among their core functions.
Final Verdict
For most shops and most belts, the Swanson S0101 is still the square to buy first: solid aluminum, two graduation increments, the full common and hip-valley scale set, and the Blue Book in the box. The Empire e2994 is the readability pick, with laser-etched high-visibility markings and scribe notches. The Johnson 1959-0700 adds a magnetic heel and continuous scribing grooves for rip layout and steel work. The IRWIN 1794464 is the straightforward deep-marked aluminum option, and the Swanson Speedlite trades metal for a light, surface-friendly 12-inch polymer body.
Related guides
Read next
- Best Marking Knives for Clean, Accurate Layout Lines
- Best Combination Squares for Layout and Machine Setup
- Best Marking Gauges for Mortise and Tenon Joint Layout
- Best Try Squares and Engineer Squares for Layout Work
- Best Pipe Clamps for Glue-Ups, Panels and Cabinet Work
- Best Spring Clamps for Woodworking and Workshop Tasks
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.




Write Your Review
No reviews yet. Be the first to share your experience!