Key takeaways
- Compare the best replacement plane irons for bench and block planes, with widths, steels and thicknesses matched to Stanley Bailey plane sizes.
What's inside
- Table of Contents
- Stanley 12-313 Replacement Plane Iron
- Jorgensen No. 4 and No. 5 Wood Planer Blade
- WoodRiver V3 Replacement Blade for No. 3 Bench Plane
- TorSor 2-Pack Bench Plane Blade
- Jorgensen No. 60-1/2 Block Plane Blade
- Replacement Chip Breakers: When the Breaker Is the Problem
- How to Choose a Replacement Plane Iron
- FAQ
- Conclusion
- Table of Contents
- Stanley 12-313 Replacement Plane Iron
- Jorgensen No. 4 and No. 5 Wood Planer Blade
- WoodRiver V3 Replacement Blade for No. 3 Bench Plane
- TorSor 2-Pack Bench Plane Blade
- Jorgensen No. 60-1/2 Block Plane Blade
- Replacement Chip Breakers: When the Breaker Is the Problem
- How to Choose a Replacement Plane Iron
- FAQ
- Conclusion
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Best Replacement Plane Irons and Chip Breakers for 2026
- Top Pick: Stanley 12-313 Replacement Plane Iron
- Runner-up: Jorgensen No. 4 and No. 5 Wood Planer Blade
- Also consider: WoodRiver V3 Replacement Blade for No. 3 Bench Plane
If your bench plane chatters, tears out figured grain, or will not hold an edge through a single board, the fastest fix is a fresh iron. The best all-around replacement is a modern 2-inch iron ground to the Bailey pattern, like the Stanley 12-313 or the Jorgensen No. 4 and No. 5 blade, because both drop into the most common smoothing and jack planes without filing the mouth. Restoring a smaller No. 3 calls for the WoodRiver V3 blade, budget-minded shops can keep a TorSor two-pack as spares, and block plane owners need the narrower Jorgensen 60-1/2 blade. This guide also covers the chip breaker half of the assembly, since a poorly fitting breaker can undo a new blade’s benefit.
As an Amazon Associate, we earn from qualifying purchases.
Contents
- Table of Contents
- Stanley 12-313 Replacement Plane Iron
- Jorgensen No. 4 and No. 5 Wood Planer Blade
- WoodRiver V3 Replacement Blade for No. 3 Bench Plane
- TorSor 2-Pack Bench Plane Blade
- Jorgensen No. 60-1/2 Block Plane Blade
- Replacement Chip Breakers: When the Breaker Is the Problem
- How to Choose a Replacement Plane Iron
- FAQ
- Conclusion
Table of Contents
- Stanley 12-313 Replacement Plane Iron
- Jorgensen No. 4 and No. 5 Wood Planer Blade
- WoodRiver V3 Replacement Blade for No. 3 Bench Plane
- TorSor 2-Pack Bench Plane Blade
- Jorgensen No. 60-1/2 Block Plane Blade
- Replacement Chip Breakers: When the Breaker Is the Problem
- How to Choose a Replacement Plane Iron
- FAQ
- Conclusion
- Product and ASIN Reference
Stanley 12-313 Replacement Plane Iron
The Stanley 12-313 is the factory answer to a worn-out Bailey iron, and the safest first choice for anyone restoring a Stanley No. 4 or No. 5. It is ground to the original 2-inch width, so it slides into the frog and mouth of a Bailey-pattern bench plane exactly the way the original iron did, with no filing. Stanley makes the iron from hardened and tempered high-carbon chrome steel, which takes a keen edge on ordinary waterstones and oilstones.
The bevel arrives ground at 25 degrees, ready for a final honing. Stanley recommends adding a 30-degree honed angle at the tip before use, standard practice that gives the edge more support in hardwoods. Current production irons are ground noticeably thicker than the thin irons fitted to early twentieth-century planes, reducing the flex that causes chatter marks on wide boards. As a genuine factory part, its slot and screw geometry match Stanley frogs precisely.
This is a mid-range, blade-only purchase; your existing chip breaker transfers over with a single screw.
Specs
- Blade width: 2 inches (50 mm)
- Steel: hardened and tempered high-carbon chrome steel
- Factory bevel: 25 degrees, with a 30-degree honed angle recommended
- Fit: Stanley Bailey bench planes, including the No. 4 and No. 5
- Surface: fine rotary ground for easier sharpening
- Contents: single replacement iron, chip breaker not included
Jorgensen No. 4 and No. 5 Wood Planer Blade
Jorgensen sells this 2-inch blade as the service replacement for its own No. 4 and No. 5 planes, and it follows the same Bailey dimensions as the Stanley pattern, so it also suits Stanley-style No. 4 smoothing and No. 5 jack planes. The blade arrives pre-ground to the correct OEM width: an iron that is even slightly wide binds in the mouth, while one that is narrow leaves gaps at the corners that pack with shavings.
Jorgensen builds its bench plane blades from hardened tool steel in the O1 family, the steel it specifies across its bench plane line, ground thick by vintage standards so the edge is well supported behind the bevel. O1-type steel hones quickly on waterstones and takes a very fine edge for smoothing work. The bevel comes ground and ready for final honing rather than fully polished, which is normal at this mid-range tier.
Measure your old iron before ordering: if it measures 2-3/8 inches across instead of 2, your plane is a No. 4-1/2, No. 5-1/2, No. 6, or No. 7, and this blade will not fit.
Specs
- Blade width: 2 inches
- Steel: hardened O1-family tool steel
- Bevel: pre-ground, ready for final honing
- Fit: No. 4 and No. 5 bench planes, Bailey pattern
- Intended planes: Jorgensen No. 4 and No. 5, plus Stanley-pattern equivalents
- Contents: single replacement blade, chip breaker not included
WoodRiver V3 Replacement Blade for No. 3 Bench Plane
No. 3 owners have far fewer choices than No. 4 owners, because the 1-3/4-inch iron is a less common size. The WoodRiver V3 replacement blade fills that gap. WoodRiver is the Woodcraft house brand, and this blade is made for the WoodRiver V3 No. 3 bench plane, ground from high-carbon tool steel. Because the No. 3 width follows the same Bailey sizing used by Stanley, it also suits a vintage Stanley No. 3 whose original iron is worn down or pitted beyond lapping.
WoodRiver grinds its V3 irons thick compared with vintage originals, and that extra steel is the point of the upgrade. A thicker iron flexes less under cutting pressure, which is what produces the fine washboard chatter woodworkers often blame on the plane body or the frog. In a small smoother reserved for final surface work, that stiffness shows up directly in the finish. The back still deserves a quick flattening pass on your finest stone before the first honing. This is the premium-leaning pick of the group, built as a quality component rather than a consumable spare.
Specs
- Blade width: 1-3/4 inches
- Steel: high-carbon tool steel
- Fit: WoodRiver V3 No. 3 bench plane and Stanley No. 3 pattern planes
- Design: thick-ground iron for reduced chatter
- Contents: single replacement blade, chip breaker not included
TorSor 2-Pack Bench Plane Blade
The TorSor two-pack takes the opposite approach from the WoodRiver: instead of one premium iron, you get two serviceable 2-inch bench plane blades in manganese steel at a budget tier. A spare iron means a nicked edge does not stop a project while you go back to the stones; you swap in the second blade and sharpen both irons together later. Many woodworkers also keep one iron of a pair ground with a heavier camber for scrub-style work and the other nearly straight for smoothing.
Manganese steel blades of this type are thinner than the premium aftermarket irons, so they behave more like a vintage original: easy to hone, but more willing to flex on an aggressive cut with the chip breaker set far back. Set the breaker close to the edge and take a moderate cut, and a thin iron performs well within its limits.
Buy the TorSor pack as insurance and as a sharpening rotation, not as a performance upgrade.
Specs
- Blade width: 2 inches
- Steel: manganese steel
- Quantity: 2 blades per pack
- Fit: standard No. 4 and No. 5 bench planes, Bailey pattern
- Contents: two replacement blades, chip breakers not included
Jorgensen No. 60-1/2 Block Plane Blade
Block planes are bevel-up, so their irons are shorter and narrower than bench plane irons, and a bench blade will never substitute. This Jorgensen blade is the replacement for the 60-1/2 pattern low-angle block plane, the most widely copied block plane design in the world. It measures 1-3/8 inches wide, the standard for 60-1/2 style planes, and drops into Jorgensen’s own No. 60-1/2 and other planes built to the same pattern.
On a low-angle block plane the iron beds bevel-up at a shallow angle, so the bevel itself forms much of the effective cutting angle. That is why block plane irons reward careful honing: a polished bevel and a small micro-bevel make a visible difference on end grain, the work these planes do most. Jorgensen grinds the blade from hardened tool steel, pre-ground so a few minutes on fine stones brings it to working sharpness.
Block plane families split into two width patterns: the 1-3/8-inch width belongs to the low-angle 60-1/2 family, while standard-angle 9-1/2 pattern planes take a wider 1-5/8-inch iron. The two are not interchangeable, so measure your old blade before ordering.
Specs
- Blade width: 1-3/8 inches
- Steel: hardened tool steel
- Orientation: bevel-up, for low-angle block planes
- Fit: 60-1/2 pattern block planes, including the Jorgensen No. 60-1/2
- Bevel: pre-ground, ready for final honing
- Contents: single replacement blade
Replacement Chip Breakers: When the Breaker Is the Problem
Every bench plane iron in this roundup is sold as a blade only, and that reflects how these assemblies wear. Chip breakers, also called cap irons, rarely wear out. A breaker deserves replacement only when its leading edge is bent, rusted into pits, or ground so unevenly that it cannot mate flat against the back of the iron. When the breaker does not seal along the iron’s back, shavings wedge into the gap, the throat clogs, and the plane feels dull no matter how sharp the edge is.
Before spending anything, test your current breaker. Lay its mating face on a flat surface and look for rocking or light gaps, then check that its front edge meets the blade evenly across the full width. Minor problems respond to flattening on a stone or on abrasive paper stuck to glass, and a breaker that passes transfers to your new iron in about a minute.
Two fitting points matter with a thicker modern iron. First, the combined stack has to fit the mouth opening; planes cast before the late 1960s were sized for thin original irons, and a thick replacement can jam or keep the frog from closing the mouth. Dry-fit before sharpening anything. Second, setback controls tear-out: a breaker edge roughly a thirty-second of an inch behind the cutting edge is the classic starting point for smoothing work.
How to Choose a Replacement Plane Iron
Start with width, because width is decided entirely by your plane’s model number. Bailey sizes run from 1-3/4 inches for a No. 3, through 2 inches for the No. 4 and No. 5, 2-1/4 inches for the No. 5-1/2, and 2-3/8 inches for the No. 4-1/2, No. 6, and No. 7, up to 2-5/8 inches for a No. 8. The number is usually stamped on the plane, but measuring the old iron settles any doubt and guards against the trap of the half sizes, which take wider irons than the base models.
Next, weigh thickness against your plane’s age. Vintage irons were thin and flex under cut, which is what chatters. Modern replacements are ground thicker, and that stiffness is the main performance gain. The trade-off is fit: a thick iron plus your chip breaker may not pass a tight vintage mouth. On pre-1970s planes, dry-fit before honing, and be ready to open the mouth slightly with a file for the thickest irons.
Then choose a steel for your sharpening habits. High-carbon and O1-family steels hone quickly on waterstones or oilstones and take a very fine edge. Harder alloy steels hold an edge longer in abrasive hardwoods but take more time on the stones. Finally, decide what you are actually fixing: a shortened, pitted, or cracked iron needs replacement, while a sound iron that merely feels dull needs honing and a better chip breaker fit.
FAQ
How do I know which width of replacement iron my plane needs?
Match the iron to the plane’s model number: a No. 3 takes a 1-3/4-inch iron, No. 4 and No. 5 planes take 2-inch irons, the No. 5-1/2 takes 2-1/4 inches, and the No. 4-1/2, No. 6, and No. 7 take 2-3/8 inches. If the casting is unmarked, measure your existing iron and order the same size.
Will a thicker replacement iron fit my vintage Stanley plane?
Usually, but not always. Planes cast before the late 1960s have mouth openings sized for thin original irons, so a thick modern iron and its chip breaker can bind against the frog or stop the mouth from closing. Dry-fit the new assembly before sharpening it. Moderate irons fit most planes unmodified; the thickest may need the mouth opened slightly with a fine file.
Do I need to replace the chip breaker when I replace the iron?
Rarely. Chip breakers wear slowly, and a flat, unbent breaker transfers to the new iron with one screw. Replace it only if its leading edge is bent, deeply pitted, or cannot be flattened to mate evenly against the iron’s back. A poor fit causes clogging that feels like a dull blade, so check the fit before blaming the new iron.
How far back should the chip breaker sit from the cutting edge?
About a thirty-second of an inch is the standard starting setback for general bench work. Setting the breaker closer increases tear-out control on figured grain, while a larger setback suits coarse jack plane work. If shavings jam between the breaker and the iron, the mating faces need flattening, not a different setback.
Conclusion
For most woodworkers, the decision is simple: a Stanley 12-313 restores a No. 4 or No. 5 to factory fit, the Jorgensen 2-inch blade covers the same planes with a thick tool steel iron, and the WoodRiver V3 gives No. 3 owners a properly stiff option in a hard-to-find size. The TorSor two-pack keeps a sharpening rotation ready at a budget tier, and the Jorgensen 60-1/2 blade handles the block plane. Whichever iron you choose, measure the old blade first, dry-fit the new assembly before honing, and check your chip breaker’s mating edge, because no iron performs behind a breaker that does not seal.
Related guides
Read next
- Best Sharpening Stones for Chisels and Plane Irons 2026
- Best Router Planes for Beginners: 5 Picks for Joinery
- Best Self-Centering Doweling Jigs: 5 Picks for 2026
- Best Diamond Sharpening Plates for Chisels and Planes
- Best Coping Saws for Beginners: 5 Easy First Picks
- Best Hand Screw Clamps for Woodworking: Top 5 Picks
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.





Write Your Review
No reviews yet. Be the first to share your experience!