Our Top Picks
SKIL 10" Dual Bevel Sliding Compound Miter Saw-MS6305-0010''35.43 x 22.44 x 14.17 inches39.4 poundsCheck on Amazon
What's inside
- Quick Answer
- DEWALT DWS779 12-Inch Double Bevel Sliding Compound Miter Saw
- Bosch GCM12SD 12-Inch Dual-Bevel Glide Miter Saw
- Makita LS1019L 10-Inch Dual-Bevel Sliding Compound Miter Saw with Laser
- Milwaukee M18 FUEL 2734-21HD 10-Inch Dual Bevel Sliding Compound Miter Saw Kit
- SKIL MS6305-00 10-Inch Dual Bevel Sliding Compound Miter Saw
- How to Choose
- Who Should Skip
- FAQ
- Final Verdict
- Quick Answer
- DEWALT DWS779 12-Inch Double Bevel Sliding Compound Miter Saw
- Bosch GCM12SD 12-Inch Dual-Bevel Glide Miter Saw
- Makita LS1019L 10-Inch Dual-Bevel Sliding Compound Miter Saw with Laser
- Milwaukee M18 FUEL 2734-21HD 10-Inch Dual Bevel Sliding Compound Miter Saw Kit
- SKIL MS6305-00 10-Inch Dual Bevel Sliding Compound Miter Saw
- How to Choose
- Who Should Skip
- FAQ
- Final Verdict
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Best Sliding Miter Saws for Home Workshops and DIY
A sliding miter saw earns its bench space by doing one thing a fixed compound saw cannot: the blade carriage travels toward you on rails or glide arms, so the saw crosscuts boards far wider than the blade diameter alone would allow. That slide turns a trim saw into a general workshop crosscut station for shelving, decking and furniture stock. Every saw below slides; a compound-only saw only chops straight down, and is a narrower tool.
As an Amazon Associate, we earn from qualifying purchases.
The five models split into two camps. The 12 inch saws from DEWALT and Bosch offer the deepest, widest cuts for bigger stock and nested crown molding, while the 10 inch saws from Makita, Milwaukee and SKIL trade a little capacity for smaller footprints, lower weight or, in the Milwaukee’s case, full cordless operation.
This article contains affiliate links, and if you buy through them the site may earn a commission at no extra cost to you.
Contents
- Quick Answer
- DEWALT DWS779 12-Inch Double Bevel Sliding Compound Miter Saw
- Bosch GCM12SD 12-Inch Dual-Bevel Glide Miter Saw
- Makita LS1019L 10-Inch Dual-Bevel Sliding Compound Miter Saw with Laser
- Milwaukee M18 FUEL 2734-21HD 10-Inch Dual Bevel Sliding Compound Miter Saw Kit
- SKIL MS6305-00 10-Inch Dual Bevel Sliding Compound Miter Saw
- How to Choose
- Who Should Skip
- FAQ
- Final Verdict
Quick Answer
The DEWALT DWS779 is the top pick for most home workshops: a 12 inch dual bevel sliding saw with a 15 amp motor, crosscut capacity of 2×14 lumber at 90 degrees and 2×10 at 45 degrees. Pick the Bosch GCM12SD if bench depth is tight, the Makita LS1019L for a wall-flush 10 inch station, the Milwaukee kit for cordless work, or the SKIL for the lightest saw.
DEWALT DWS779 12-Inch Double Bevel Sliding Compound Miter Saw
The DWS779 is DEWALT’s mainstream 12 inch slider and the reference point for this class. It is a true sliding compound saw: the head rides on rails for wide crosscuts, and it is dual bevel, tilting both ways so crown and trim can be cut without flipping the workpiece. DEWALT states crosscut capacity of 2×14 lumber at 90 degrees and 2×10 at a 45 degree miter.
The miter range runs 60 degrees right and 50 degrees left on a detent plate with 10 positive stops, and bevel reaches 49 degrees in both directions. One honest gap: this model has no laser and no LED shadow line, so cuts are lined up against blade and fence marks. At 56 pounds it is a bench saw rather than a carry-around tool.
Specs:
– Blade: 12 inch, 32 tooth blade included
– Type: Sliding compound, dual bevel
– Motor: 15 amp corded, 3,800 RPM no-load speed
– Miter range: 60 degrees right, 50 degrees left, 10 positive stops
– Bevel range: 49 degrees left and right
– Crosscut capacity: 2×14 at 90 degrees, 2×10 at 45 degrees (maker stated)
– Crown capacity: 7-1/2 inches nested
– Cut line guide: None fitted, no laser or shadow line
– Weight: 56 pounds
See the DEWALT DWS779 on Amazon
Bosch GCM12SD 12-Inch Dual-Bevel Glide Miter Saw
The Bosch takes a different mechanical route to the same job. Instead of sliding on round rails that stick out behind the saw, it uses the Axial-Glide system, a pair of articulated arms that fold as the head moves. It remains a full sliding compound saw with dual bevel, not a compound-only chop saw.
Bosch states a horizontal crosscut capacity of 14 inches at 90 degrees and 9-1/2 inches at a 45 degree miter, with 6-1/2 inches of vertical capacity against the fence. The miter range is 52 degrees left and 60 degrees right, and bevel reaches 47 degrees each way. Like the DEWALT, it has no laser or shadow line. At 65 pounds it is the heaviest saw here.
Specs:
– Blade: 12 inch, 60 tooth blade included
– Type: Sliding compound via Axial-Glide arms, dual bevel
– Motor: 15 amp corded, 3,800 RPM no-load speed
– Miter range: 52 degrees left, 60 degrees right
– Bevel range: 47 degrees left and right
– Crosscut capacity: 14 inches horizontal at 90 degrees, 9-1/2 inches at 45 degrees (maker stated)
– Vertical capacity: 6-1/2 inches against the fence
– Cut line guide: None fitted, no laser or shadow line
– Weight: 65 pounds
See the Bosch GCM12SD on Amazon
Makita LS1019L 10-Inch Dual-Bevel Sliding Compound Miter Saw with Laser
Makita’s 10 inch slider uses a two-steel-rail system that runs forward, so the rails never project behind the saw and it can operate flush against a wall. Even with the smaller blade, Makita states a crosscut capacity of 2-13/16 by 12 inches at 90 degrees, and 2-13/16 by 8-1/2 inches at a 45 degree miter.
The miter range is the widest here, 0 to 60 degrees left and right, with dual bevel from 0 to 48 degrees both ways. The 15 amp direct drive motor turns 3,200 RPM, and the L in the model name marks the built-in laser guide, the only laser in this lineup. It weighs 57.9 pounds, heavy for a 10 inch saw.
Specs:
– Blade: 10 inch
– Type: Sliding compound, forward two-rail design, dual bevel
– Motor: 15 amp corded direct drive, 3,200 RPM no-load speed
– Miter range: 0 to 60 degrees left and right
– Bevel range: 0 to 48 degrees left and right
– Crosscut capacity: 2-13/16 by 12 inches at 90 degrees, 2-13/16 by 8-1/2 inches at 45 degrees (maker stated)
– Crown capacity: 6-5/8 inches nested
– Cut line guide: Built-in laser
– Weight: 57.9 pounds
See the Makita LS1019L on Amazon
Milwaukee M18 FUEL 2734-21HD 10-Inch Dual Bevel Sliding Compound Miter Saw Kit
This listing is the kit version of Milwaukee’s M18 FUEL 10 inch slider, model 2734-21HD, bundling the 2734-20 saw with one M18 REDLITHIUM HIGH DEMAND 9.0 battery pack and a rapid charger. It runs entirely on the 18 volt M18 platform, and its brushless motor spins the blade at 4,000 RPM.
Milwaukee states crosscut capacity of 2×12 at 90 degrees and 2×8 at a 45 degree miter, plus 5-3/4 inches of vertical capacity for baseboard against the fence. The miter range is 50 degrees left and 60 degrees right, bevel reaches 48 degrees both ways, and an LED shadow cut line shows where the blade will land. The bare saw weighs 45 pounds, the lightest full-size slider here.
Specs:
– Blade: 10 inch, carbide tipped blade included
– Type: Sliding compound, dual bevel, cordless
– Power: M18 FUEL brushless, one 9.0Ah battery and rapid charger included in this kit, 4,000 RPM no-load speed
– Miter range: 50 degrees left, 60 degrees right
– Bevel range: 48 degrees left and right
– Crosscut capacity: 2×12 at 90 degrees, 2×8 at 45 degrees (maker stated)
– Vertical capacity: 5-3/4 inches against the fence
– Cut line guide: LED shadow cut line
– Weight: 45 pounds (tool only)
See the Milwaukee 2734-21HD kit on Amazon
SKIL MS6305-00 10-Inch Dual Bevel Sliding Compound Miter Saw
The SKIL is the straightforward DIY pick: a corded 10 inch sliding compound saw with dual bevel, a 15 amp motor and the fastest blade speed here at 4,800 RPM. SKIL states crosscut capacity of 2×12 at 90 degrees and 2×8 at 45 degrees, enough for flooring, framing repairs and most furniture parts.
The bevel system tilts 48 degrees left and 45 degrees right with positive stops at 48 and 45 degrees left, zero, and 45 degrees right, while the miter table swings 50 degrees each way with 11 positive stops. An LED shadow line marks the cut. The listing gives an item weight of 39.4 pounds, the easiest saw here to move between bench, stand and storage.
Specs:
– Blade: 10 inch
– Type: Sliding compound, dual bevel
– Motor: 15 amp corded, 4,800 RPM no-load speed
– Miter range: 50 degrees left and right, 11 positive stops
– Bevel range: 48 degrees left, 45 degrees right
– Crosscut capacity: 2×12 at 90 degrees, 2×8 at 45 degrees (maker stated)
– Cut line guide: LED shadow line
– Weight: 39.4 pounds (listing stated)
See the SKIL MS6305-00 on Amazon
How to Choose
Start with the widest board you cut regularly. If that is 2×12 shelving or decking, every saw here handles it at 90 degrees; if you crosscut 2×14 stock or wide crown, only the two 12 inch models qualify. Then check the 45 degree figure rather than the headline number, because miter capacity drops fast: the DEWALT still manages 2×10, while the 10 inch saws fall to 2×8 or a stated 8-1/2 inch width.
Next, match the slide mechanism to your bench. Rail sliders like the DEWALT and SKIL need clear space behind the saw for rail travel, while the Bosch glide arms and Makita forward rails work close to a wall. Finally decide on power and guidance: corded saws run all day, the Milwaukee kit trades runtime for freedom from outlets, and a laser or shadow line speeds up alignment for occasional users.
Who Should Skip
Skip this whole category if your cutting is mostly ripping long boards lengthwise; that is table saw work, and a miter saw is the wrong tool. Skip the 12 inch models if your shop is a folding stand in a shared garage, since both weigh more than 55 pounds and the Bosch reaches 65. Skip the Milwaukee kit if you own no other M18 tools and never cut away from an outlet, since the battery platform premium buys you nothing. And skip every saw here if your widest stock is narrow trim; a smaller compound-only saw cuts trim all day, as long as you accept its narrower crosscut limit.
FAQ
Is a 10 inch or 12 inch sliding miter saw better for a home workshop?
It depends on stock size. A 10 inch slider crosscuts 2×12 lumber at 90 degrees, which covers most home projects. A 12 inch saw adds capacity for 2×14 stock, taller baseboard and larger nested crown, at the cost of weight and bench space.
What is the difference between a sliding and a compound-only miter saw?
A compound miter saw only pivots down into the work, so crosscut width is limited by blade diameter. A sliding model adds rails or glide arms that let the blade travel across the board, roughly doubling usable width. All five saws here slide; compound-only saws are a separate, narrower category.
Do I need dual bevel?
Dual bevel lets the blade tilt both left and right, so you can cut matching bevels on crown molding and trim without turning the workpiece around. For long or fragile trim that flipping is awkward and risks damage, so dual bevel is worth having; every saw listed here includes it.
How accurate is a laser or shadow line guide?
Both project the blade position onto the work before the cut. A laser draws a line on the cut path, while a shadow line casts the blade’s own shadow and shows the exact kerf width. Either is a setup aid rather than a guarantee, and the DEWALT and Bosch manage without one.
Final Verdict
For a permanent home workshop station, the DEWALT DWS779 is the safest all-round buy, with the widest stated crosscut capacity and dual bevel. The Bosch GCM12SD is the pick when wall clearance decides, and the Makita LS1019L delivers near-12-inch capacity in a wall-flush 10 inch frame. The Milwaukee 2734-21HD kit is the cordless route for M18 owners, and the SKIL MS6305-00 gives DIY users dual bevel sliding capacity in the lightest package of the five.
Related guides
Read next
- Best Benchtop Band Saws for Home Woodworking Shops
- Best Miter Gauges for Table Saws: 5 Accurate Picks
- Best Hand Tools for a Home Woodshop: Five Workshop Staples
- Best Workshop Maintenance Essentials for Home Garages
- Best Diamond Sharpening Plates for Plane Irons and Chisels
- Best Table Saw Blades for Fine Woodworking Projects
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.




Write Your Review
No reviews yet. Be the first to share your experience!