Our Top Picks
WEN CT1065 10-Amp 6.5-Inch Plunge Cut Sidewinder CircularTrack Saw12 x 6 x 5 inches0 poundsCheck on Amazon
What's inside
- Quick Answer
- Makita SP6000J1 Plunge Saw Kit with 55-Inch Guide Rail
- Festool TS 55 FEQ-F-Plus-FS Track Saw with 55-Inch Guide Rail
- Makita XPS01PTJ 36V (18V X2) LXT Brushless Cordless Plunge Saw Kit
- Kreg ACS-SAW Plunge Saw with 62-Inch Guide Track
- WEN CT1065 10-Amp Plunge Cut Track Saw
- How to Choose
- Who Should Skip
- FAQ
- Final Verdict
- Quick Answer
- Makita SP6000J1 Plunge Saw Kit with 55-Inch Guide Rail
- Festool TS 55 FEQ-F-Plus-FS Track Saw with 55-Inch Guide Rail
- Makita XPS01PTJ 36V (18V X2) LXT Brushless Cordless Plunge Saw Kit
- Kreg ACS-SAW Plunge Saw with 62-Inch Guide Track
- WEN CT1065 10-Amp Plunge Cut Track Saw
- How to Choose
- Who Should Skip
- FAQ
- Final Verdict
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Best Track Saws for Clean and Straight Plywood Cuts
A track saw earns its place in the shop by doing one job better than any other portable tool: breaking down full sheets of plywood into straight, clean-edged parts. Instead of wrestling a 4×8 sheet across a table saw, you lay a guide rail on the sheet, set the saw on the rail, and plunge. The rail controls the line, its rubber splinter strip supports the veneer at the cut, and the edge comes off the saw ready for glue or edge banding.
As an Amazon Associate, we earn from qualifying purchases.
The five track saws below differ in ways that matter more than spec gaps. Some include a rail and some do not; the included rails sit in the 55-inch class, which crosscuts a sheet easily but cannot rip one lengthwise. Four run on cords, one runs on a battery platform, and each brand uses its own rail profile, so the saw you choose also chooses your future rails and accessories.
This article contains affiliate links, and if you buy through one of them, we may earn a commission at no additional cost to you.
Contents
- Quick Answer
- Makita SP6000J1 Plunge Saw Kit with 55-Inch Guide Rail
- Festool TS 55 FEQ-F-Plus-FS Track Saw with 55-Inch Guide Rail
- Makita XPS01PTJ 36V (18V X2) LXT Brushless Cordless Plunge Saw Kit
- Kreg ACS-SAW Plunge Saw with 62-Inch Guide Track
- WEN CT1065 10-Amp Plunge Cut Track Saw
- How to Choose
- Who Should Skip
- FAQ
- Final Verdict
Quick Answer
For most plywood work, the Makita SP6000J1 is the top pick among these track saws. It is a corded 12-amp plunge saw sold with a 55-inch guide rail in the box, it cuts 2-3/16 inches deep at 90 degrees, and its bevel range runs from -1 to 48 degrees, so it crosscuts full sheet widths cleanly right out of the case.
Makita SP6000J1 Plunge Saw Kit with 55-Inch Guide Rail
The SP6000J1 is the most complete starter package here: the box holds the corded saw, a 55-inch guide rail, a 48-tooth carbide blade, and a stackable case, so it crosscuts plywood the day it arrives. The rail gives roughly 49 to 50 inches of usable cut once saw overhang is counted, covering a sheet’s 48-inch width with room to spare. It does not rip an 8-foot sheet lengthwise; that takes a second joined rail or Makita’s longer rail, sold separately.
The 12-amp motor has variable speed from 2,000 to 5,200 RPM, useful for melamine and laminates that chip easily, plus an electronic brake. The rail’s splinter guard strip is trimmed by the blade on the first cut, so the strip edge becomes your exact cut line, and its depth also covers door trimming and thick worktop cutouts.
Specs:
– Power source: corded, 12-amp motor
– Speed: variable, 2,000 to 5,200 RPM
– Blade: 6-1/2 inch, 48-tooth carbide blade included
– Depth of cut: 2-3/16 inches at 90 degrees; 1-9/16 inches at 45 degrees
– Bevel range: -1 to 48 degrees, positive stops at 22.5 and 45 degrees
– Track included: yes, 55-inch guide rail
– Riving knife: not stated
See it on Amazon: https://www.amazon.com/dp/B00CHN6L74?tag=powertoolsdiy04-20
Festool TS 55 FEQ-F-Plus-FS Track Saw with 55-Inch Guide Rail
The TS 55 FEQ-F-Plus-FS is the current version of Festool’s benchmark plunge saw, bundled with the FS 1400 guide rail. The same rail math applies as with the Makita kit: a 55-inch rail crosscuts the width of a 4×8 sheet comfortably, but ripping the full length needs a longer Festool rail or two joined together, inside Festool’s own FS system.
The corded 1,200-watt motor runs from 2,000 to 5,800 RPM, and the saw carries a riving knife that follows the blade to reduce binding in solid wood. An attachable splinterguard is included; Festool describes guard and rail strip together as giving virtually splinter-free cuts on both sides of the blade. The cut line stays put when the saw tilts for a bevel, too.
Specs:
– Power source: corded, 1,200-watt motor
– Speed: variable, 2,000 to 5,800 RPM
– Blade: 160 mm (6-1/4 inch class), 48-tooth fine-cut blade included
– Depth of cut: 2-3/16 inches at 90 degrees; 1-11/16 inches at 45 degrees
– Bevel range: -1 to 47 degrees
– Track included: yes, FS 1400 guide rail, 55 inches
– Splinter protection: attachable splinterguard included
See it on Amazon: https://www.amazon.com/dp/B0897YPSF8?tag=powertoolsdiy04-20
Makita XPS01PTJ 36V (18V X2) LXT Brushless Cordless Plunge Saw Kit
The XPS01PTJ is the cordless option here, aimed at shops already running Makita’s 18V LXT platform. Two 18V batteries deliver 36V to a brushless motor, and the kit includes two 5.0Ah batteries, a rapid charger, a 55-tooth blade, and a case. Depth matches the corded Makita at 2-3/16 inches at 90 degrees, so cordless costs nothing in capacity.
The catch is the rail: this kit does not include one. Makita rails are sold separately, in shorter, 55-inch, and longer sheet-ripping lengths, so budget for one before comparing this kit with the corded kits above. Makita does build in a depth stop for a shallow scoring pass of about 2 to 3 mm, the standard trick for keeping face veneer from tearing on the final plunge.
Specs:
– Power source: cordless, 36V from two 18V LXT batteries, brushless motor
– Kit contents: saw, two 18V LXT 5.0Ah batteries, rapid charger, tool case
– Speed: variable, 2,500 to 6,300 RPM
– Blade: 6-1/2 inch, 55-tooth blade included
– Depth of cut: 2-3/16 inches at 90 degrees; 1-9/16 inches at 45 degrees
– Bevel range: -1 to 48 degrees, positive stops at 22.5 and 45 degrees
– Track included: no, guide rail sold separately
See it on Amazon: https://www.amazon.com/dp/B01IVTAO8Y?tag=powertoolsdiy04-20
Kreg ACS-SAW Plunge Saw with 62-Inch Guide Track
Kreg’s entry ships with the longest track in this group. The 62-inch Guide Track gives up to 50 inches of cutting capacity, the most generous crosscut margin here, so the saw never runs off the end of the rail on sheet widths. Like every setup in this class, though, it cannot rip a full 8-foot length in one pass, and Kreg’s track profile is its own, so only Kreg track extends it.
The saw itself is a corded 12-amp model with variable speed, a retractable riving knife, and an electronic brake, a safety pairing the corded Makita kit lacks. Depth is a touch shallower at 2-1/8 inches at 90 degrees, still enough for doubled-up sheet goods and most cabinet stock. It also pairs with Kreg’s Adaptive Cutting System table, though the saw and track work on any flat sheet setup.
Specs:
– Power source: corded, 12-amp motor
– Speed: variable speed; exact RPM range not stated
– Blade: 6-1/2 inch
– Depth of cut: 2-1/8 inches at 90 degrees; 1-1/2 inches at 45 degrees
– Bevel range: -1 to 47 degrees
– Track included: yes, 62-inch Guide Track (50-inch cutting capacity)
– Riving knife: yes, retractable
See it on Amazon: https://www.amazon.com/dp/
WEN CT1065 10-Amp Plunge Cut Track Saw
The WEN CT1065 is the entry-level way into track sawing, and its listing needs careful reading: this ASIN is the saw alone, with a 24-tooth carbide blade and no track in the box. WEN’s matching CT9502 track runs 100 inches in two 50-inch sections, sold separately. Bought together, that track is the longest setup here and the only one that rips a full 8-foot sheet in a single setup, once the sections are joined and checked for straightness.
The corded 10-amp motor spins at a fixed 5,500 RPM, with no dial for slowing down in plastics or laminates. It does offer, unusually at this level, a three-position blade setting with a dedicated scoring mode about 1/8 inch deep, so you score the veneer first and plunge fully on the second pass. Depth capacity is the deepest here at up to 2-1/3 inches, though the bevel range is the narrowest, stopping at 45 degrees with no undercut.
Specs:
– Power source: corded, 10-amp motor
– Speed: 5,500 RPM, fixed
– Blade: 6-1/2 inch, 24-tooth carbide-tipped blade included, 20 mm arbor
– Depth of cut: up to 2-1/3 inches at 90 degrees; 1-5/8 inches at 45 degrees
– Bevel range: 0 to 45 degrees
– Track included: no, WEN CT9502 100-inch track sold separately
– Warranty: two-year warranty
See it on Amazon: https://www.amazon.com/dp/B07VFXFTVP?tag=powertoolsdiy04-20
How to Choose
Start with rail length, because it decides what the saw can do on a 4×8 sheet. A 55-inch or 62-inch rail crosscuts the 48-inch width with room for saw entry and exit, but its usable cut is only about 49 to 50 inches, far short of a 96-inch rip. If ripping full sheets lengthwise is a weekly job, plan on a 100-inch class track like the WEN setup, or two same-brand rails joined with that brand’s connectors, checked against a long straightedge before trusting the joint.
Next, choose corded or cordless honestly. Corded saws never stop mid-sheet for a battery swap, and two here include the rail. The cordless XPS01PTJ makes the most sense when you already own LXT batteries, and its rail is a separate purchase. Depth differences are small, and every saw here cuts 3/4-inch plywood with room to spare, so depth only matters for thick solid stock or stacked sheets.
Finally, treat splinter control as a system: rail splinter strip, fine-tooth blade, splinterguard where fitted, and a scoring pass on veneer-faced sheets all work together. And accept the lock-in: rails, connectors, clamps, and splinter strips follow one brand’s profile, so pick a system you are happy to stay inside.
Who Should Skip
Skip the whole category if you break down one or two sheets a year; a circular saw with a clamped straightedge, or the lumber yard’s cutting service, will cost far less. Skip it, too, if most of your work is narrow rips in solid boards, where a table saw is faster and more repeatable.
Also skip any 55-inch class kit if your main job is ripping full sheets lengthwise with no budget for the longer rail. And if you already own one brand’s rails, skip a bargain saw from another brand; it starts a second, incompatible system.
FAQ
Can a 55-inch track rip a full 4×8 sheet of plywood lengthwise?
No. A 55-inch rail delivers roughly 49 to 50 inches of usable cut once saw overhang is counted, enough for the 48-inch crosscut but nowhere near the 96-inch length. Full-length rips need a track in the 100-inch class, or two same-brand rails joined with connectors.
Are track saw rails interchangeable between brands?
Plan on no. Each maker uses its own rail profile, splinter strip position, and accessory fittings, and sells rails and clamps as brand-specific parts. A saw may physically slide on another brand’s rail, but fit, cut-line accuracy, and accessory support are not guaranteed, so buy rails and accessories from the same brand as your saw.
Is a cordless track saw as capable as a corded one for plywood?
For sheet goods, yes. The cordless Makita here matches the corded saws on depth and bevel range, and plywood does not demand sustained heavy power. The real differences are runtime on long ripping sessions, battery cost off-platform, and the rail being a separate purchase.
Final Verdict
For a complete, ready-to-cut package, the Makita SP6000J1 is the easiest recommendation: corded power, a 55-inch rail in the box, and depth and bevel numbers covering cabinet work. The Festool is the refinement pick, with its splinterguard, riving knife, and deep accessory system. Choose the XPS01PTJ if you are invested in LXT batteries and accept buying the rail separately, the Kreg for the longest included track, and the WEN if the budget rules, knowing its separate 100-inch track makes it the only full-length ripping setup here.
Related guides
Read next
- Best Miter Bench Hooks for Clean, Accurate Hand Saw Cuts
- Best Router Template Guide Bushings for Clean Cuts
- Best Tenon Jigs for Table Saws: 5 Picks for Clean Cheeks
- Best Track Saws for Small Workshops: 5 Compact Picks
- Best Quick-Release Dog Hole Clamps for Workbenches in 2026
- Best Wood Carving Tool Sets for Beginners and Detail Work
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.


Write Your Review
No reviews yet. Be the first to share your experience!