Key takeaways
- Compare the best hole saw kits for wood and plywood by diameter range, arbor type, blade material, cutting depth, piece count and included case.
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Best Hole Saw Kits for Wood, Plywood and Soft Materials
A hole saw kit is the fastest way to bore clean, round openings in wood and plywood: door lock bores, pass-throughs for pipes and cables, grommet holes in a desktop, or cutouts for recessed fittings. Instead of buying saws one at a time, a kit bundles a spread of diameters with the arbors and pilot bits that drive them in a single case. The catch is that kits differ in what the piece count actually buys you, how deep the saws cut, and how the arbor system handles size changes.
As an Amazon Associate, we earn from qualifying purchases.
This guide compares five kits currently sold on Amazon, from compact six-saw sets to a 19-piece carbon steel kit that reaches 5 inches. Four are bi-metal trade kits from DEWALT, Milwaukee, LENOX and Bosch; the fifth is a wood-only carbon steel set from HYCHIKA. Every specification below is quoted as the maker publishes it; where a maker does not publish a figure, that is stated rather than guessed.
This article contains affiliate links, and fdwoodworking.com may earn a commission on qualifying purchases made through them.
Quick Answer
The DEWALT D180005 is the strongest all-round pick: 11 bi-metal saws from 3/4 inch to 2-1/2 inches, two quick-change mandrels, Pilot Point bits and a molded case cover most woodworking diameters. Choose the LENOX 308021200L for holes up to 4-3/4 inches, the Bosch HSBIM9 for a compact two-arbor set, or the HYCHIKA HS17K for wide, shallow holes in soft sheet goods.
The Five Kits Compared
DEWALT D180005 14-Piece Master Hole Saw Kit
DEWALT calls this its Master kit because it merges the sizes from its plumber’s, electrician’s and door lock kits into one box. The 11 bi-metal saws run from 3/4 inch to 2-1/2 inches, covering lock bores, most pipe pass-throughs and standard grommet holes. DEWALT describes a double tooth design for strength and durability, a deep-cut geometry, and thick, hardened backing plates intended to prevent thread stripping. Two quick-change mandrels, one small and one large, handle the full size range, and a replacement parts set with two Pilot Point centering bits is included for when a pilot bit dulls or snaps.
Specs
– Total pieces: 14
– Hole saws: 11 bi-metal saws in 3/4, 7/8, 1, 1-1/8, 1-3/8, 1-1/2, 1-3/4, 2, 2-1/8, 2-1/4 and 2-1/2 inch sizes
– Blade material: bi-metal, double tooth design
– Mandrels: small and large quick-change mandrels
– Pilot bits: Pilot Point bits plus replacement parts set
– Cutting depth: not stated numerically; deep-cut geometry per DEWALT
– Case: injection-molded kit box included
See the DEWALT D180005 on Amazon
Milwaukee 49-22-4029 Hole Dozer Bi-Metal Hole Saw Kit, 17-Piece
Milwaukee’s general purpose Hole Dozer kit packs nine bi-metal saws spanning 3/4 inch to 2-1/2 inches into a customizable storage case, with arbors and pilot bits making up the rest of the 17-piece count. The line is built around two maker-stated features: Rip Guard teeth, backed by a limited lifetime tooth break warranty, and Plug Jack all-access slots in the cup wall that give a pry tool full access for levering out wood plugs. A low-friction thermoset coating is applied to the saws, which Milwaukee says supports faster cutting in wood. For plywood work, the plug ejection slots are the highlight, since thin discs wedge tightly in shallow cups.
Specs
– Total pieces: 17
– Hole saws: 9 bi-metal Hole Dozer saws, 3/4 inch to 2-1/2 inches
– Blade material: bi-metal with Rip Guard tooth form and thermoset coating
– Plug removal: Plug Jack all-access slots
– Arbors and pilot bits: included; specific models not stated
– Cutting depth: not stated
– Case: storage case included
See the Milwaukee 49-22-4029 on Amazon
LENOX 308021200L Speed Slot Electrician’s Hole Saw Kit, 17-Piece
This is the kit to look at when 2-1/2 inches is not big enough. The LENOX electrician’s kit carries 12 bi-metal saws from 3/4 inch up to 4-3/4 inches, adding the large diameters used for recessed lighting, vent pass-throughs and conduit entries. The Speed Slot name refers to the staircase-shaped slot in the cup wall: the steps give a screwdriver staged leverage points for prying out plugs, which matters most on the large saws where a stuck plywood disc is hardest to shift. LENOX states the current generation uses increased wall thickness to minimize tooth loss, with larger, sharper teeth for fast cutting in wood. Two SNAP-BACK arbors and three pilot drills are included.
Specs
– Total pieces: 17
– Hole saws: 12 bi-metal Speed Slot saws in 3/4, 7/8, 1-1/8, 1-3/8, 1-3/4, 2, 2-1/2, 2-11/16, 3, 3-5/8, 4-1/8 and 4-3/4 inch sizes
– Blade material: bi-metal, Speed Slot staircase plug-ejection design
– Arbors: SNAP-BACK 2L and 5L arbors
– Pilot drills: two 4321 and one 56PD pilot drills
– Blade length: 44 mm as listed
– Kit weight: 7.74 lb as listed
– Case: large kit case included
See the LENOX 308021200L on Amazon
Bosch HSBIM9 9-Piece Bi-Metal Hole Saw Kit
The Bosch kit is the compact option: six bi-metal saws covering 3/4 inch to 2 inches, enough for lock work, cable grommets and small plumbing holes in plywood. The listing describes the saws as bi-metal made with an 8 percent cobalt alloy, and Bosch fits its Progressor tooth design, which alternates tooth sizes and is intended to cut faster and last longer across wood, metal and plastic. Two SpinLOCK universal arbors are included; Bosch states the universal arbor fits all brands and sizes and allows tool-free accessory installation. A steel pilot bit, hex key and plastic case round out the nine pieces, and Bosch publishes a 1.75 inch working length, the clearest depth figure in this group.
Specs
– Total pieces: 9
– Hole saws: 6 bi-metal saws in 3/4, 7/8, 1-1/8, 1-1/2, 1-3/4 and 2 inch sizes
– Blade material: bi-metal with 8 percent cobalt alloy as described in the listing; Progressor tooth design
– Arbors: two SpinLOCK universal arbors, 1/4 inch and 7/16 inch
– Pilot bit: steel pilot bit included, plus a hex key
– Working length: 1.75 inches as published by Bosch
– Case: plastic carrying case included
See the Bosch HSBIM9 on Amazon
HYCHIKA HS17K 19-Piece Hole Saw Kit
The HYCHIKA set trades blade material for diameter range. Its 13 blades are heat-treated carbon steel with a black oxide finish, running from 3/4 inch to 5 inches, the widest spread in this comparison. The maker is explicit about intended materials: soft wood, plywood, drywall, PVC and plastic plate, with a stated maximum cutting depth of 25 mm. That depth is the trade-off to understand: a 25 mm cup handles plywood, MDF and drywall comfortably but will not pass through a 2x framing member in one cut. Two mandrels, two drill bits, an installation plate and a hex key are included, along with a storage case.
Specs
– Total pieces: 19
– Hole saws: 13 carbon steel blades from 3/4 inch (19 mm) to 5 inches (127 mm)
– Blade material: heat-treated carbon steel with black oxide finish
– Mandrels: 2 mandrels, 1/4 inch and 3/8 inch as described by the maker
– Accessories: 2 drill bits, installation plate and hex key included
– Maximum cutting depth: 25 mm as stated by the maker
– Case: storage case included
See the HYCHIKA HS17K on Amazon
How to Choose
Start with diameter coverage, not piece count. A 17-piece kit may hold only nine saws, while a 14-piece kit holds eleven, so count the saws and check them against the holes you actually bore: 2-1/8 inches for locksets, 1-3/8 or 1-1/2 inches for many pipe runs, and 4 inches or more for recessed lights and vents. Next, match cutting depth to your stock. Plywood and sheet goods forgive a shallow cup, but boring through a 2x stud or a workbench top needs a deeper saw or a willingness to clear the plug and cut from both sides; where a maker publishes a working length, as Bosch does, compare it with your material thickness.
Blade material decides versatility. Bi-metal saws, with a high-speed steel cutting edge, are the right default for woodworkers because the same kit also handles plastic, thin metal and the occasional nail-embedded board. Carbon steel kits like the HYCHIKA cover bigger diameters, but the maker limits them to soft materials and they dull faster in hardwood. Finally, look at the arbor system. Quick-change and universal arbors speed up size swaps, while basic threaded mandrels are slower but simple. Check shank sizes against your drill’s chuck, and treat plug-removal slots as a real feature: on production-style plywood work, ejecting discs is where the time goes.
Who Should Skip
Skip these kits if your holes are mostly in hardwood furniture stock and you need a clean, splinter-free rim on the show face; a Forstner bit usually leaves a tidier edge in that situation. Skip the carbon steel HYCHIKA if you ever cut metal, hardwood or stock thicker than its stated 25 mm depth. Skip hole saws entirely for very large diameters in thick timber, where a jigsaw or router with a circle jig is more controllable, and skip the big trade kits if you only ever bore one size, such as a single lockset diameter; one saw and an arbor is the simpler purchase. None of these kits is rated by its maker for masonry, tile or cement board.
FAQ
Can these hole saw kits cut metal as well as wood?
The four bi-metal kits are rated by their makers for wood, plastic and metal, so occasional thin sheet metal or aluminum is within their stated scope. The HYCHIKA HS17K is the exception: its maker lists soft wood, plywood, drywall, PVC and plastic plate only, so treat it as a soft-materials kit.
What kind of drill do these kits need?
All five kits use standard arbors and mandrels with hex or round shanks sized for common drill chucks, including the 1/4 inch and 7/16 inch arbors in the Bosch kit. Larger diameters in thick stock call for a drill with enough torque and a side handle; makers generally recommend lower speeds as diameter grows.
Will these saws cut through a 2x stud in one pass?
That depends on the published depth. Bosch states a 1.75 inch working length for the HSBIM9, which matches a nominal 2x member’s actual thickness. The HYCHIKA’s stated 25 mm maximum depth will not do it in one pass, so clear the plug partway and finish from the other side. Where a maker does not publish a depth figure, plan on the two-sided approach.
Are arbors interchangeable between brands?
Threaded hole saws from the major makers generally share common thread sizes, and Bosch explicitly states its SpinLOCK universal arbor fits all brands and sizes. Proprietary quick-change systems, however, are designed around their own ecosystems, so check the arbor standard before assuming a saw from one kit will mount on another kit’s mandrel.
Final Verdict
For most woodworkers, the DEWALT D180005 hits the balance point: the widest useful spread of everyday diameters in this group, two quick-change mandrels, spare pilot bits and bi-metal durability in one case. The Milwaukee 49-22-4029 suits anyone who bores plywood all day and values fast plug ejection; the LENOX 308021200L is the clear choice when the job list includes holes above 2-1/2 inches. The Bosch HSBIM9 suits smaller, tidier work with a published working length and universal arbors, and the HYCHIKA HS17K earns its place only for wide, shallow holes in soft sheet goods.
Related guides
Read next
- Best Brad Point Drill Bits for Clean Holes in Wood
- Best Wood Finishes for Cyber Monday 2026: Buy or Wait
- Best Table Saw Accessories to Buy for Black Friday 2026
- Best Wood Fillers for Repairs, Grain and Stain Work
- Best Pipe Clamps for Glue-Ups, Panels and Cabinet Work
- Best Speed Squares for Layout, Roofing and Shop Marking
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.





Write Your Review
No reviews yet. Be the first to share your experience!