Key takeaways
- Compare the best brad point drill bits for wood: five sets checked for steel type, size range, shank style and case, plus how to choose the right set.
What's inside
- Quick Answer
- Fisch 29-Piece Chrome Vanadium Brad Point Drill Bit Set (FSF-364757)
- DEWALT 6-Piece Brad Point Drill Bit Set (DW1720)
- Century Drill & Tool 37280 25-Piece Brad Point Index Set
- NordWolf 12-Piece Brad Point Drill Bit Set with Hex Shank
- WoodRiver 29-Piece Fractional Brad Point Drill Bit Index Set
- How to Choose
- Who Should Skip
- FAQ
- Final Verdict
- Quick Answer
- Fisch 29-Piece Chrome Vanadium Brad Point Drill Bit Set (FSF-364757)
- DEWALT 6-Piece Brad Point Drill Bit Set (DW1720)
- Century Drill & Tool 37280 25-Piece Brad Point Index Set
- NordWolf 12-Piece Brad Point Drill Bit Set with Hex Shank
- WoodRiver 29-Piece Fractional Brad Point Drill Bit Index Set
- How to Choose
- Who Should Skip
- FAQ
- Final Verdict
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Best Brad Point Drill Bits for Clean Holes in Wood
A standard twist bit meets wood with a blunt cone, so it tends to skate across the surface and tear fibres as it starts. A brad point bit is ground differently. A sharp centre spur touches first and digs in, locating the hole exactly on your mark before anything else cuts. Two outer spurs then score the circumference, severing the fibres cleanly around the rim. Only then do the flutes lift chips from the middle. Because the rim is cut before the centre is excavated, the entry hole keeps a crisp edge, even in plywood and veneered board, where twist bits leave fuzz and tear-out.
As an Amazon Associate, we earn from qualifying purchases.
This guide compares five brad point sets covering the main ways woodworkers buy them: full fractional indexes, a compact set of core cabinet sizes, and a quick-change hex shank set for cordless drills. The sets use the three steels makers commonly offer, carbon steel, high-speed steel and chrome vanadium, with notes on how each handles heat and wear. One limit applies to every set here: brad point bits are wood bits, not metal bits.
This article contains affiliate links, and we may earn a commission when you buy through them at no extra cost to you.
Contents
- Quick Answer
- Fisch 29-Piece Chrome Vanadium Brad Point Drill Bit Set (FSF-364757)
- DEWALT 6-Piece Brad Point Drill Bit Set (DW1720)
- Century Drill & Tool 37280 25-Piece Brad Point Index Set
- NordWolf 12-Piece Brad Point Drill Bit Set with Hex Shank
- WoodRiver 29-Piece Fractional Brad Point Drill Bit Index Set
- How to Choose
- Who Should Skip
- FAQ
- Final Verdict
Quick Answer
For most woodworkers, the Fisch 29-piece chrome vanadium set is the top pick: it covers 1/16 to 1/2 inch in fine steps, its ground spurs cut clean entry holes in hardwood and sheet goods, and the case keeps every size organised. Choose the DEWALT DW1720 instead if you only need the six common cabinet sizes.
Fisch 29-Piece Chrome Vanadium Brad Point Drill Bit Set (FSF-364757)
Fisch makes its bits in Austria, and this 29-piece set is the fullest fractional range in this guide, running from 1/16 to 1/2 inch in 1/64 inch steps. That fine spacing matters: for dowel and hardware work, a snug hole and a sloppy one often differ by a single 64th. The bits are chrome vanadium steel with beveled, precision-ground edges, positioned by Fisch for clean cutting in softwood, hardwood, laminated board and MDF.
The spurs are ground sharp, which produces the clean entry holes the design promises, and the set arrives in a handled case that keeps the index sorted. For pilot holes, dowel joints and hardware boring without size gaps, this is the set to build around.
Specs:
– Material: Chrome vanadium steel
– Pieces: 29
– Sizes: 1/16 to 1/2 inch in 1/64 inch increments
– Edge: Beveled cutting edge, precision ground
– Case: Storage case with carry handle
– Country of origin: Austria
– Shank type: not stated
View it on Amazon: https://www.amazon.com/dp/B078P375Z5?tag=powertoolsdiy04-20
DEWALT 6-Piece Brad Point Drill Bit Set (DW1720)
The DW1720 takes the opposite approach to the big indexes: just six bits, in the sizes cabinet and furniture work calls for most often. DEWALT states the bits are high-speed steel, with precise cutting edges shaped to reduce splintering and engineered flutes that clear chips efficiently. The brad point tip reduces walking at the start of the hole, which helps on finished faces where a wandering bit would scar the work.
The size run covers the common dowel diameters and most pilot and clearance holes. It makes a sensible first set, or a compact second set for a jobsite bag, if you accept that in-between sizes need another set. DEWALT does not list a case, so plan on a pouch or index box of your own.
Specs:
– Material: High-speed steel
– Pieces: 6
– Sizes: 1/8, 3/16, 1/4, 5/16, 3/8, 1/2 inch
– Tip: Brad point, designed to reduce walking
– Flutes: Engineered for chip removal
– Case: not stated
– Shank type: not stated
View it on Amazon: https://www.amazon.com/dp/B005GOM3VO?tag=powertoolsdiy04-20
Century Drill & Tool 37280 25-Piece Brad Point Index Set
Century Drill & Tool is a long-running American bit maker, and the 37280 is its fractional brad point index: 25 pieces in high-speed steel, covering 1/8 to 1/2 inch, in an index case that keeps each bit in a labelled slot. The index case makes grabbing the right diameter fast and shows which sizes are missing.
High-speed steel is the practical draw here. HSS holds its hardness at higher temperatures than carbon steel, so the edges keep working through longer sessions in dense hardwood, where friction heat builds quickly. For a drill press station boring repeated dowel holes, that is a real advantage over carbon steel.
Specs:
– Material: High-speed steel
– Pieces: 25
– Sizes: 1/8 to 1/2 inch, fractional
– Case: Index storage case
– Shank type: not stated
View it on Amazon: https://www.amazon.com/dp/B07THB95PG?tag=powertoolsdiy04-20
NordWolf 12-Piece Brad Point Drill Bit Set with Hex Shank
Every bit in the NordWolf set carries a 1/4 inch hex shank, so the bits snap into quick-change holders and standard chucks alike and swap in seconds on a cordless drill. That suits assembly work away from the bench, where swapping between a pilot bit and a driver bit happens all day. The bits use a double flute design and are listed for hardwood, plywood and plastic.
The 12 pieces span 1/8 to 1/2 inch SAE, and the set doubles up the sizes that see the most wear, including 1/8, 3/16 and 1/4 inch, so a dulled small bit does not stop the job. One trade-off: hex shanks trade trueness for speed of change, so round shank sets run better for precision drill press work. NordWolf does not state the bit steel.
Specs:
– Material: not stated
– Pieces: 12
– Sizes: 1/8 to 1/2 inch SAE, with duplicates of the most-used sizes
– Shank: 1/4 inch hex, quick-change
– Flutes: Double flute design
– Listed uses: Hardwood, plywood, plastic
– Case: not stated
View it on Amazon: https://www.amazon.com/dp/B09WKDR897?tag=powertoolsdiy04-20
WoodRiver 29-Piece Fractional Brad Point Drill Bit Index Set
WoodRiver is the house brand of Woodcraft, and this 29-piece index matches the Fisch on coverage, running 1/16 to 1/2 inch in 1/64 inch steps in a sturdy storage case. The bits are carbon steel, and WoodRiver is upfront about the geometry: bits 1/8 inch and larger carry a true brad point, while the smallest bits below that size use a simpler point. Bits up to 3/8 inch have full-diameter shanks, which grip securely in the chuck.
Carbon steel takes a keen edge, but it gives up hardness sooner than high-speed steel when friction heat builds, so this set suits hand drill and drill press work at sensible speeds rather than long production runs in dense hardwood. For a home shop drilling mostly pine, poplar and plywood, the steel is entirely adequate, and the full index is the appeal.
Specs:
– Material: Carbon steel
– Pieces: 29
– Sizes: 1/16 to 1/2 inch in 1/64 inch increments
– Point: True brad point on bits 1/8 inch and larger
– Shanks: Full diameter on bits up to 3/8 inch
– Case: Index storage case
View it on Amazon: https://www.amazon.com/dp/B01M1LD2QJ?tag=powertoolsdiy04-20
How to Choose
Start with the point. Clean entry holes come from sharp outer spurs that score the rim before the flutes lift chips, so favour sets whose makers describe ground or beveled spurs; blunt spurs tear like a twist bit. The centre spur should be straight and centred, since it locates the hole.
Next, match the steel to your workload. Carbon steel bits are keen, but the steel loses hardness as heat builds, so they dull sooner in long hardwood runs. High-speed steel keeps its hardness at higher temperatures and suits drill press production work. Chrome vanadium, as Fisch uses it, is a hard-wearing wood-bit steel that holds a ground edge well. None of this changes the basic rule: these bits are for wood and wood-based sheet goods, not metal.
Then count sizes honestly. Dowel joints commonly need 1/4, 5/16 and 3/8 inch, shelf pins take 1/4 inch holes, and most screw pilot work falls between 1/8 and 1/2 inch. A six-piece set covers those core jobs; a 25 or 29-piece index adds the in-between 64ths that fitted work demands. For shanks, round shanks in a three-jaw chuck or drill press run truest, while hex shanks trade a little precision for instant changes in cordless drills.
Technique matters as much as the set. Published speed charts suggest smaller bits run faster and larger bits slower; a 1/2 inch bit, for example, is listed around 750 rpm in hardwood and 1,800 rpm in softwood. In a hand drill, start slowly so the spurs score the rim, then feed steadily and clear chips on deep holes.
Who Should Skip
Skip brad point bits entirely if your drilling is mostly metal; the thin centre spur and outer spurs will chip and dull quickly in steel, and a standard twist bit set is the right tool there. Skip them, too, if you mainly bore large holes for locks or plumbing, since brad point sets stop at 1/2 inch and spade or Forstner bits handle bigger diameters better.
Skip the big 29-piece indexes if you only ever drill two or three sizes; a compact set like the DW1720 covers core cabinet sizes without a case of bits that never leave their slots. Skip carbon steel sets if you run long, repetitive drilling in dense hardwood, where heat builds fast; high-speed steel holds its edge longer.
FAQ
Can brad point bits drill metal?
No. The centre spur and thin outer spurs are ground to sever wood fibres, and in steel or other metals they chip, fold or dull almost immediately. Keep a separate twist bit set for metal and use brad points only in wood and sheet goods.
What is the difference between a brad point bit and a twist bit?
The tip geometry. A twist bit has a conical point that skates on entry and tears fibres as the full diameter engages. A brad point bit locates with a centre spur, scores the rim with two outer spurs, then lifts chips from inside that scored circle, which is why its entry holes are cleaner.
What speed should a brad point bit run at?
Published speed charts put smaller diameters faster and larger diameters slower. From those charts, a 1/2 inch bit runs around 750 rpm in hardwood and 1,800 rpm in softwood, while a 1/8 inch bit runs around 1,200 rpm in hardwood and 1,800 rpm in softwood. If the wood scorches, slow down and clear chips more often.
How do I stop tear-out where the bit exits?
Clamp a sacrificial backer board tightly under the workpiece so the spurs exit into wood instead of bursting through unsupported fibres. For through holes in fine work, drill until the centre spur just pokes through, then finish from the other side using that mark to locate the bit.
Final Verdict
For a single set that does everything this guide describes, the Fisch 29-piece chrome vanadium index is the strongest choice, with the finest size steps, sharp ground spurs and a proper case. The DEWALT DW1720 suits buyers who only need the six core cabinet sizes, while the Century 37280 brings high-speed steel to a 25-piece index for heavier drill press use. The NordWolf set is the cordless, quick-change option, and the WoodRiver index is a full-range carbon steel set for lighter shop work. Match the steel and size range to your drilling, keep the bits in wood only, and any of the five will cut clean entry holes.
Related guides
Read next
- Best Countersink Drill Bit Sets for Clean Screw Holes
- Best Random Orbit Sanders for Smooth Wood Finishes
- Best Japanese Wood Chisel Sets for Fine Joinery Work
- Best Wood Glues for Furniture and Cabinet Projects
- Best Hand Screw Clamps for Woodworking: Top 5 Picks
- Best Carving Gouges and Chisel Sets for Spoon Carving
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.



Write Your Review
No reviews yet. Be the first to share your experience!