Key takeaways
- The Wixey WR365 digital angle gauge reads blade and fence angles in 0.1 degree steps, with a flip-up display, magnetic base and built-in level readout.
What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Wixey WR365 Digital Angle Gauge Review for Woodworkers
Setting a table saw blade or a miter saw fence by eye is mostly guesswork, and the error usually shows up later as a gap in a miter joint or a frame that will not close. The Wixey WR365 is a small digital angle gauge built to remove that guesswork. It sits against a blade, fence or table surface and shows the angle on a flip-up display, turning setup into a quick reading instead of a trial cut followed by another adjustment.
The gauge measures across a range of plus or minus 180 degrees, which covers everything from a square 90 degree crosscut to steep bevel settings. It also carries a built-in absolute level readout, a magnetic aluminum base with a V-groove for round stock, and it runs on two AAA batteries. For woodworkers who swap between rip, crosscut and bevel work on the same machines, it promises faster, more repeatable setup.
As an Amazon Associate, we earn from qualifying purchases.
Contents
Quick answer
The Wixey WR365 is a compact digital angle gauge for setting saw blades, miter fences and jointer tables. It reads angles across a plus or minus 180 degree range in 0.1 degree steps, sticks to steel surfaces with a magnetic base, and doubles as an absolute level. It suits woodworkers who want repeatable machine setup without guesswork.
Key specs
| Spec | Detail |
|---|---|
| Model | WR365 |
| Measuring range | Plus or minus 180 degrees |
| Resolution | 0.1 degree |
| Accuracy | Within 0.2 degrees |
| Display | Flip-up digital display |
| Level function | Built-in absolute level readout |
| Base | Magnetic aluminum base with V-groove |
| Power | Two AAA batteries |
Design and everyday use
The WR365 is small enough to live in an apron pocket or a drawer beside the table saw, which matters because a setup tool only helps if it is within reach. The display flips up so the reading stays visible whether the gauge stands on a table, sticks to the side of a blade, or tilts against a miter fence. The flip-up screen keeps the large digits readable from a natural working position instead of forcing the user to crouch and read sideways.
The base is where the design earns its keep. It is machined from aluminum and fitted with magnets, so it holds firmly to a steel saw blade, a cast iron table or a jointer fence. The V-groove cut into the base lets it sit steadily on round stock, which makes it useful for checking a drill press quill, a lathe tool rest or pipe needing a consistent bevel. The workflow is simple: zero the gauge on the machine table, move it to the blade, and read the true blade angle rather than relying on the saw’s own stamped scale.
In day-to-day shop use, the gauge covers many jobs. It sets table saw blade tilt, checks that a miter saw returns to an exact 90 degrees, squares a jointer fence, and verifies drill press table tilt. The built-in absolute level readout adds a second role: leveling machine stands, checking that a workbench sits flat, or confirming a shelf cleat is level before it is fixed. Accuracy within 0.2 degrees is tighter than most stamped saw scales, and the 0.1 degree resolution means small corrections show up on screen immediately instead of after a test cut.
Power comes from two AAA batteries, a common size most shops already keep on hand. There is no cord and nothing to charge, which suits a tool that may sit unused for a week and then be needed for thirty seconds of setup.
Who it’s for / who should skip
This gauge is for woodworkers who cut miters, bevels and angled joinery often enough that setup accuracy shows in the finished work: picture framers, box makers and cabinet builders. It also suits owners of older saws whose built-in angle scales have drifted or were never precise.
Skip it if your work is almost entirely square cuts made with a sled or a fixed fence, since a good square already answers those questions. Woodworkers who only need rough carpentry angles will find a basic protractor adequate, and anyone who dislikes battery-powered gadgets may prefer a mechanical bevel gauge with slower, less precise readings.
How it compares with alternatives
The main alternatives are mechanical bevel gauges, the angle scales built into the saw itself, and larger digital protractors. A traditional sliding bevel gauge transfers an angle but never tells you what that angle is, and reading it against a protractor adds another step and another chance for error. Built-in saw scales are convenient but are often stamped, hard to read and only approximate, which is why a blade set to a marked 45 degrees so often produces joints that do not close.
Larger digital protractors can match this gauge for readout precision, but they are bulkier and lack the magnetic base that makes one-handed blade checks so quick. The WR365 occupies a useful middle ground: small, magnetic, able to reference both a surface-relative zero and an absolute level, and quick enough that checking an angle becomes a habit rather than a chore.
FAQ
Can the WR365 measure a blade angle relative to the saw table?
Yes. Zero the gauge on the table surface, then place it against the blade. The display shows the blade angle relative to the table, the number that matters for bevel and miter settings.
What does the absolute level readout add?
Beyond relative angles, the gauge shows level against gravity, which suits leveling machine stands, benches and installed work where no machine table is available to zero against.
How does the V-groove in the base help?
The groove lets the magnetic base sit securely on round material such as pipe, dowels or a drill press column, where a flat base would rock on the curve and the reading would wander.
What batteries does it use?
It runs on two AAA batteries, which are inexpensive and widely available, so a spare pair in the shop drawer is all the preparation the tool needs.
Final verdict
The Wixey WR365 does one job and does it well: it turns angle setting from estimation into measurement. The wide plus or minus 180 degree range, 0.1 degree resolution, magnetic V-groove base and dual role as an absolute level make it a useful addition to any shop that cuts angles on a table saw, miter saw or jointer. For woodworkers tired of test cuts and creeping miter gaps, it is an easy tool to justify.
Related guides
Read next
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.

Write Your Review
No reviews yet. Be the first to share your experience!