Updated Nov 19, 2026· 5 min read

Key takeaways

  • The Stanley Sweetheart No. 4 pairs a thick A2 iron with a Norris-type adjuster for fine smoothing. Check the specs, strengths, and who it suits most here.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

The No. 4 smoothing plane is the last plane to touch most boards before finishing, responsible for leaving a surface that is flat, clean, and ready for oil or varnish. The Stanley Sweetheart No. 4, model 12-136, is a modern production version of that classic pattern. It pairs a one-piece base and frog casting with a thick A2 steel iron, a cherry handle and knob, and a Norris-type adjuster, aiming for the stability and fine control that smoothing work demands.

This review looks at how those features translate to the bench: what the thick iron and solid frog do for chatter and tear-out, how the Norris-type adjuster changes blade setting, and where a No. 4 fits alongside jack and jointer planes. It also covers who gets the most from this plane and when a different size or style serves better.

As an Amazon Associate, we earn from qualifying purchases.

Contents
  1. Quick answer
  2. Key specs
  3. Design and everyday use
  4. Who it’s for / who should skip
  5. How it compares with alternatives
  6. FAQ
  7. Final verdict

Quick answer

The Stanley Sweetheart No. 4 is a smoothing bench plane built around a one-piece base and frog and a 1/8-inch thick A2 steel iron with a 2-inch cutter. Its Norris-type adjuster combines depth and lateral control in one mechanism, and the cherry handle and knob suit long smoothing sessions. For final surface preparation by hand, it is a capable, traditional choice.

Key specs

Specification Detail
Brand Stanley
Model 12-136
Plane type No. 4 smoothing bench plane
Iron A2 steel, 1/8 in thick
Cutter width 2 in
Base and frog One-piece casting
Handle and knob Cherry wood
Adjuster Norris-type

Design and everyday use

The frog is the part of a bench plane that supports the iron, and its fit decides how calmly the plane cuts. On the Sweetheart No. 4, the base and frog are a one-piece casting, so the iron rests on a solid, unified bed rather than on a separate frog that can shift or rock. That solidity helps resist chatter, the vibration that leaves rippled marks across a board, and it supports the fine, even shavings a smoothing plane exists to take.

The iron itself is 1/8 inch thick and made of A2 steel, with a cutter 2 inches wide. A thicker iron flexes less under cutting pressure, which again works against chatter, and A2 is known for holding a keen edge through long sessions on abrasive woods. The trade-off is that A2 takes a little more patience on the sharpening stones than softer steels, so a consistent honing routine is part of owning this plane.

Adjustment comes from a Norris-type mechanism, which combines depth setting and lateral alignment in a single adjuster rather than splitting them between separate controls. Small, deliberate movements are exactly what smoothing calls for when the goal is a wispy shaving and a surface free of tear-out. The cherry handle and knob round out the design with warm, comfortable grips that suit the steady, two-handed stroke the plane rewards.

Who it’s for / who should skip

Who it’s for: Woodworkers who finish surfaces by hand will appreciate what this plane is built to do. It suits furniture makers preparing tabletops and panels for finish, and anyone who wants a new smoothing plane in the classic pattern without taking on the restoration work an old, neglected plane often needs.

Who should skip: Anyone whose main task is removing rough, cupped stock should start with a jack plane, whose longer sole and cambered iron are made for that stage. Flattening long boards calls for a jointer plane instead. And woodworkers who surface everything with power planers and sanders will find little use for a dedicated smoothing plane.

How it compares with alternatives

Vintage No. 4 planes in the same pattern can be excellent, but they vary widely in condition and often need cleaning, flattening, and tuning before they cut well. Premium boutique planes offer heavier castings and tighter tolerances for makers who want that level of refinement. Low-angle smoothing planes take a different approach, with a bevel-up iron that some woodworkers prefer for difficult grain and end grain. Jack planes are more versatile across rough and fine work but lack the short sole that lets a smoother follow a board’s surface. The Sweetheart No. 4 occupies a clear position: a new, traditionally patterned smoother with a thick A2 iron and a unified base and frog, ready for final surface work.

FAQ

What is a No. 4 smoothing plane used for?

A No. 4 is the finishing step in hand surfacing. After boards have been flattened and thicknessed with other planes, the smoother takes fine shavings to remove marks, calm tear-out, and leave a surface ready for finish. Its short sole follows the board closely, which is what makes it a smoother rather than a flattening tool.

What does the Norris-type adjuster do?

It combines blade depth adjustment and lateral alignment in one mechanism. That gives the user fine, controlled movement of the iron from a single control, which helps when setting the plane to take very light shavings and correcting a cut that favors one side.

How thick is the iron on the Sweetheart No. 4?

The iron is 1/8 inch thick, made of A2 steel, and the cutter is 2 inches wide. The extra thickness compared with thinner irons helps the blade resist flexing and chatter during the cut, and the A2 steel is chosen for edge retention.

Is a smoothing plane a good first bench plane?

It depends on the work. A No. 4 excels at final smoothing, but it is not designed for flattening rough or twisted lumber. Woodworkers starting from rough stock usually pair a smoother with a jack plane for the earlier stages, then finish with the No. 4 as the last step before finish is applied.

Final verdict

The Stanley Sweetheart No. 4 takes the classic smoothing plane pattern and builds it around stability: a one-piece base and frog, a 1/8-inch A2 iron, and a Norris-type adjuster for fine, combined control. The cherry handle and knob make it comfortable through long sessions of final surface work. For woodworkers who smooth tabletops and panels by hand, it is a dependable finishing plane; those focused on rough stock removal should look to a jack or jointer plane first.

F
FD Woodworking Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Stanley Sweetheart No. 4 Plane Review: Smooth ResultsCheck price on Amazon

Related guides

Browse all Uncategorized guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.