Key takeaways
- Five adjustable fly cutters for drill presses compared: diameter ranges, shanks, cutter bits, and materials, from woodworking to sheet metal.
What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Buying Guides › Best Drill Press Fly Cutters for Clean Round Holes
A fly cutter turns a drill press into a circle-cutting machine. One adjustable arm, one cutting bit, and a pilot point let a single tool cover a wide range of hole diameters, so a shop can cut speaker openings, duct holes, and round blanks without keeping a drawer full of fixed-size hole saws. The design looks simple, and it is, but the spinning arm demands respect: clamp the work, lock every screw, and keep the feed slow and steady.
The five tools below share that single-point design. One is a classic woodworking model for drill-press use only, and the other four are adjustable hole cutters for sheet metal that mount in a drill chuck and run in a drill press. Each pick lists its diameter range, shank, cutter bit, and rated materials.
As an Amazon Associate, we earn from qualifying purchases.
Contents
Quick answer
For woodworking on a drill press, the General Tools 55 leads: it cuts 1-3/4 to 7-7/8 inch circles with a 1/2 inch shank and a 500 RPM limit. For sheet metal, the Malco HC1 leads with a 2 to 12 inch range and a replaceable mill-type bit. The other three picks share the same single-point design at lower tiers, and every pick needs a clamped workpiece and a slow feed.
General Tools 55 Heavy Duty Circle Cutter
The General Tools 55 is the heavy-duty end of the classic General circle-cutter line, and it is the pick for woodworkers who want a dedicated drill-press fly cutter. Its heat-treated tool steel body carries a graduated beam, so the cutting radius reads off the tool instead of a separate ruler. The 1/2 inch round shank seats in a full-size drill-press chuck, and the maker sets a 500 RPM maximum safe speed, which suits the slowest belt setting on most drill presses.
Both cutting parts are replaceable: a 1/4 inch high-speed steel bit does the cutting, and a 1/4 inch pilot drill holds the center while the arm swings. A hex wrench comes with the tool for diameter and depth adjustments. The 1-3/4 to 7-7/8 inch range covers small lids, round blanks, and speaker and vent openings, and the published material list runs from wood and plastic to sheet metal, brass, copper, soft steel, and aluminum.
Specs
- : Diameter range: 1-3/4 to 7-7/8 inches. Shank: 1/2 inch round. Cutter bit: replaceable 1/4 inch high-speed steel bit. Pilot: replaceable 1/4 inch pilot drill. Body: heat-treated tool steel with a graduated beam. Maximum safe speed: 500 RPM. Hex wrench included. Catalog code: 21012.
Malco HC1 Sheet Metal Hole Cutter
The Malco HC1 is the professional sheet-metal pick, built in the USA around a lightweight aluminum frame with sealed bearings at the top and bottom of the drill shaft. Those bearings keep the spinning arm balanced at the 1350 RPM the maker recommends for its high-speed steel mill-type bit. A combination English and metric diameter gauge sits on the adjustable pivot slide, so the hole size sets with a slide and a lock instead of guesswork.
The HC1 cuts 2 to 12 inch holes in galvanized sheet metal up to 20-gauge, with published capacity for aluminum, copper, and mild steel as well. It mounts in any drill with a 1/4 inch or larger chuck, and the same frame works in a drill press for shop work. The single replaceable mill-type bit wears only through the thickness of the material cut, so nudging it up or down exposes a fresh cutting edge and extends its life.
Specs
- : Diameter range: 2 to 12 inches. Capacity: up to 20-gauge galvanized steel, plus aluminum, copper, and mild steel. Cutter bit: replaceable mill-type high-speed steel bit. Frame: lightweight aluminum with sealed bearings and a combination English and metric diameter gauge on the pivot slide. Chuck: fits 1/4 inch or larger drill chucks. Weight: 16 ounces. Recommended speed: 1350 RPM for the high-speed steel bit. Made in the USA.
PMTHMPTS Adjustable Sheet Metal Hole Cutter
The PMTHMPTS adjustable hole cutter follows the same single-point pattern as the pro models: an adjustable arm, a pivot point, and one high-speed steel cutter bit. Its 2 to 12 inch range matches the Malco HC1, and its published capacity covers 24-gauge steel, 26-gauge stainless steel, and 20-gauge galvanized sheet metal. That spread makes it a general-purpose pick for ductwork, roofing, and ceiling installs.
Its 1/4 inch shank seats in a standard drill chuck or a drill-press chuck without an adapter. The single-blade layout keeps setup simple: slide the arm to the diameter, lock it, center the pivot, and feed slowly. It covers the same diameters as the premium picks with fewer parts to manage.
Specs
- : Diameter range: 2 to 12 inches. Capacity: 24-gauge steel, 26-gauge stainless steel, and 20-gauge galvanized sheet metal. Cutter bit: high-speed steel. Mount: 1/4 inch shank for drill chucks. Use: HVAC ductwork, roofing, and ceiling installs.
ZGTools Metal Cutter Hole Tool
The ZGTools metal cutter hole tool is the value pick in this roundup, and its headline feature is practical rather than flashy: the kit includes one extra HC1B bit alongside the fitted cutter. Spare bits matter because the bit is the wear part, and a dull bit drags, heats, and tears instead of cutting. Having a spare keeps a duct job moving without a separate order.
The tool itself cuts 2 to 12 inch circles in 24-gauge carbon steel and 26-gauge stainless steel, with a 1/4 inch mount for drill chucks. It suits the same HVAC ductwork and sheet-metal duct cutting as the other sheet-metal picks, and one tool replaces a set of fixed hole saws across its whole range. Set the diameter on the slide, lock the arm, and let the bit cut at its own pace.
Specs
- : Diameter range: 2 to 12 inches. Capacity: 24-gauge carbon steel and 26-gauge stainless steel. Cutter bit: high-speed steel, with 1 extra HC1B bit included. Mount: 1/4 inch shank. Use: HVAC ductwork and sheet-metal duct cutting.
HURRICANE Adjustable Hole Cutter
The HURRICANE adjustable hole cutter rounds out the roundup as the compact sheet-metal pick. Its metal body measures 7.3 by 4.5 by 1.2 inches and weighs 1.06 pounds, which keeps the tool easy to handle overhead or on a ladder when cutting duct takeoffs. The 2 to 12 inch range covers the same diameters as the other sheet-metal picks, and the published capacity is 24-gauge steel and 26-gauge stainless steel.
Model 02-208 mounts in a drill chuck and suits HVAC ductwork and roofing holes, the same work the Malco pattern serves. The single cutting bit and adjustable pivot slide follow the familiar fly-cutter layout, so anyone who has used one adjustable hole cutter can set this one without learning a new system. For a shop that wants a second adjustable cutter, it covers the common duct sizes.
Specs
- : Diameter range: 2 to 12 inches. Capacity: 24-gauge steel and 26-gauge stainless steel. Model: 02-208. Body: metal. Dimensions: 7.3 x 4.5 x 1.2 inches. Weight: 1.06 pounds. Mount: drill chuck. Use: HVAC ductwork and roofing.
How to choose
Begin with the diameter range. The General Tools 55 covers 1-3/4 to 7-7/8 inches, while the four sheet-metal picks cover 2 to 12 inches. If your work is mostly small round blanks and lids, the smaller range is enough; if you cut duct takeoffs and ceiling openings, the 12 inch top end matters more.
Next, match the shank to your chuck. The General Tools 55 needs a 1/2 inch chuck, while the sheet-metal picks mount through a 1/4 inch shank. Check your drill press chuck before ordering, and remember that the woodworking model is drill-press only while the sheet-metal models also run in a handheld drill.
Then look at the material rating. The woodworking model lists wood, plastic, and thin non-ferrous metals, while the sheet-metal picks rate by gauge: 24-gauge steel, 26-gauge stainless, and 20-gauge galvanized. Never ask a thin-sheet cutter to punch through thick plate, and never run a woodworking fly cutter beyond its published list.
Speed is the safety line. The General Tools model caps at 500 RPM, while Malco recommends 1350 RPM for its high-speed steel bit in sheet metal. Run the slowest setting your machine allows for the woodworking model, clamp the workpiece to the table, keep hands clear of the swing, and feed the quill slowly. A sharp bit cuts cleaner than a dull one, so favor models with spare bits available.
Who should skip
Skip the fly-cutter format entirely if you have no drill press and no drill stand, at least for the woodworking model. A fly cutter with a long swinging arm is not a handheld tool, and freehand use invites the arm to grab, kick, or throw the workpiece. The sheet-metal models mount in a handheld drill, but even there a firm grip and a clamped workpiece are required.
Skip it too if your holes are deep or your stock is thick. A fly cutter slices through thin sheet and boards, and it cannot bore a deep flat-bottomed hole the way a Forstner bit can. For stopped, angled, or overlapping holes, a Forstner or an auger bit is the right tool.
Finally, skip the adjustable format if every hole you cut is one fixed size. A fixed hole saw sets up faster and repeats without measuring, while a fly cutter earns its keep when diameters change from job to job. If you cut the same 4 inch opening all day, the adjustable arm is setup time you do not need.
Frequently asked questions
Can a fly cutter run in a handheld drill?
The woodworking model is drill-press only. The sheet-metal models mount in a drill chuck as small as 1/4 inch, so they run in a handheld drill, but a drill press or a drill stand gives a steadier cut and keeps hands away from the swinging arm.
What speed should a drill press run with a fly cutter?
Follow the maker figure for your model. The General Tools 55 caps at 500 RPM, so use the slowest belt setting on your drill press. Malco recommends 1350 RPM for its high-speed steel mill-type bit in sheet metal. In both cases, clamp the work, lock every screw, and feed slowly.
How do I set the cutting diameter?
Slide the arm or the pivot pin along the graduated scale until the distance from the pilot point to the cutting edge equals the radius you need, then lock it with the hex wrench. Measure twice before cutting, and confirm the lock is tight, since a loose arm changes diameter while the tool spins.
What materials can a fly cutter handle?
Match the model to its published list. The General Tools 55 lists wood, plastic, sheet metal, brass, copper, soft steel, and aluminum. The sheet-metal picks rate by gauge, such as 24-gauge steel, 26-gauge stainless steel, and 20-gauge galvanized steel. Stay inside the rated gauge and material list for the model you own.
Final verdict
The General Tools 55 is the pick for woodworkers: a dedicated drill-press fly cutter with a graduated beam, replaceable bit and pilot, and a 500 RPM limit that suits the slowest drill-press setting. The Malco HC1 is the pick for sheet metal, with sealed bearings, a dual-scale gauge, and a replaceable mill-type bit. The PMTHMPTS, ZGTools, and HURRICANE picks cover the same 2 to 12 inch sheet-metal range, with the ZGTools kit adding a spare bit. Whichever model you choose, clamp the work, lock the arm, and let the bit cut at its own pace.
Product and ASIN Reference
| Product | ASIN |
|---|---|
| General Tools 55 Heavy Duty Circle Cutter | B00004T7P1 |
| Malco HC1 Sheet Metal Hole Cutter | B000289542 |
| PMTHMPTS Adjustable Sheet Metal Hole Cutter | B0FM79572H |
| ZGTools Metal Cutter Hole Tool | B0FS76KCF8 |
| HURRICANE Adjustable Hole Cutter | B0FNQB2GP6 |
Related guides
Read next
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.





Write Your Review
No reviews yet. Be the first to share your experience!