Key takeaways
- Compare the best benchtop wood lathes for bowls, pens and small shops, with swing, centers, spindle thread, tapers and speed ranges for each pick.
What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Best Benchtop Wood Lathes for Bowls, Pens and Small Shops
- Top Pick: JET JWL-1221VS Variable Speed Wood Lathe
- Runner-up: Delta 46-460 Variable Speed MIDI Lathe
- Also consider: WEN LA3424 5-Speed Benchtop Wood Lathe
A benchtop lathe earns its place in a small shop by doing three jobs well: holding a bowl blank steady at low speed, spinning a pen blank fast and true, and staying put on the bench while it works. The five machines below cover that ground at different sizes, from compact 8-inch mini lathes for pen turners to 12-inch midi lathes that can rough out a serving bowl.
As an Amazon Associate, we earn from qualifying purchases.
The numbers that matter most are swing over bed, distance between centers, spindle thread, and the Morse taper in the headstock and tailstock, because those figures decide what work fits and which chucks and centers you can mount. Each pick lists them exactly as the maker publishes them, with the speed control type and included accessories.
This article contains affiliate links, and we may earn a commission when you buy through them at no extra cost to you.
Contents
Quick Answer
The JET JWL-1221VS is the top pick for most small shops: a 12-1/2-inch swing, 20-1/2 inches between centers, a 1 HP motor, and electronic variable speed across three belt ranges from 60 to 3,600 RPM, with forward and reverse. Pen turners short on bench space should look at the WEN LA3421 instead.
JET JWL-1221VS Variable Speed Wood Lathe
JET builds the JWL-1221VS around a cast iron bed and a 1 HP, 115V motor, and it is the most capable machine here. The 12-1/2-inch swing handles bowl blanks that would overwhelm a mini lathe, and the 20-1/2 inches between centers covers chair spindles and longer work without a bed extension.
Speed control is electronic variable speed inside three belt ranges of 60-900, 110-1,800, and 220-3,600 RPM, with a digital readout and a ratchet-style belt tension system for range changes. A switch flips the spindle from forward to reverse, which helps when sanding bowls. The spindle thread is 1 inch by 8 TPI, and both headstock and tailstock take MT2 tapers, so standard chucks and centers fit.
At 121 pounds it is the heaviest lathe here, which keeps it planted during roughing cuts but makes it a semi-permanent bench resident. Amazon lists the included components as the lathe, tools, hardware, and tool supports.
Specs:
– Swing over bed: 12-1/2 inches
– Distance between centers: 20-1/2 inches
– Motor: 1 HP, 115V, single phase
– Speed control: Electronic variable speed in three belt ranges, 60-900, 110-1,800, and 220-3,600 RPM, digital readout
– Spindle thread: 1 inch x 8 TPI
– Headstock and tailstock taper: MT2
– Included accessories: Lathe, tools, hardware, and tool supports, as listed
– Faceplate size: not stated
– Weight: 121 pounds
See the JET JWL-1221VS on Amazon
Delta 46-460 Variable Speed MIDI Lathe
The Delta 46-460 has been a benchmark midi lathe for years, built around a 1 HP maximum motor and a 12-1/2-inch swing over the bed. Delta rates the distance between centers at 16-1/2 inches, and an optional modular bed extension lengthens that for spindle work.
Speed changes combine a belt move with electronic variable control, giving three ranges of 250-750, 600-1,800, and 1,350-4,000 RPM as Delta publishes them. Like the JET, it offers forward and reverse rotation for finishing work. The spindle thread is 1 inch by 8 TPI, and the headstock and tailstock tapers are both #2 Morse taper.
Delta includes a 3-inch faceplate, two tool rests at 6 inches and 10 inches, a ball-bearing live center, a spur center, and a steel knockout bar, with onboard storage for the adjustment tools.
Specs:
– Swing over bed: 12-1/2 inches
– Distance between centers: 16-1/2 inches
– Motor: 1 HP maximum, 120V
– Speed control: Electronic variable speed in three belt ranges, 250-750, 600-1,800, and 1,350-4,000 RPM
– Spindle thread: 1 inch x 8 TPI
– Headstock and tailstock taper: #2 MT
– Included accessories: 3-inch faceplate, 6-inch and 10-inch tool rests, live center, spur center, knockout bar
– Weight: not stated
See the Delta 46-460 on Amazon
WEN LA3424 5-Speed Benchtop Wood Lathe
The WEN LA3424, also sold as the 3424T, matches the midi class on capacity with a 12-inch swing and 18 inches between centers, but keeps speed control simple with belt-step pulleys. The 4.5-amp motor drives five fixed speeds of 520, 900, 1,400, 2,150, and 3,400 RPM, changed by moving the belt between pulley steps.
That fixed-speed layout is a fair trade for many turners: there is no electronics package to worry about, and the five steps cover roughing, shaping, and finishing speeds. The spindle thread is 1 inch by 8 TPI, and the headstock and tailstock tapers are MT2, so it shares the common accessory standard with the JET and Delta above.
WEN includes a 3-1/8-inch faceplate, an 8-inch tool rest, a spur center, and a live center, plus an onboard accessory holder. At 70.3 pounds it is far easier to move on and off a shared bench than the two heavier midis.
Specs:
– Swing over bed: 12 inches
– Distance between centers: 18 inches
– Motor: 4.5-amp
– Speed control: Belt-step pulleys, five speeds of 520, 900, 1,400, 2,150, and 3,400 RPM
– Spindle thread: 1 inch x 8 TPI
– Headstock and tailstock taper: MT2
– Included accessories: 3-1/8-inch faceplate, 8-inch tool rest, spur center, live center, onboard accessory holder
– Weight: 70.3 pounds
Shop Fox W1704 Benchtop Lathe
The Shop Fox W1704 is the traditional mini lathe in this group, with cast iron construction, an 8-inch swing, and 13 inches between centers. That capacity covers pens, bottle stoppers, small bowls, and short spindles, which is the workload most hobby turners actually do.
Its 1/3 HP motor runs through electronic variable speed spanning 750 to 3,200 RPM as the maker publishes it, so speed changes happen at the dial rather than under a belt cover. Two tool rests are included, along with a faceplate for mounting bowl blanks, a spur center, and a live center.
At roughly 41 to 52 pounds depending on the published figure, it is light enough to carry to a workbench and store on a shelf between sessions. The spindle thread and taper sizes are not stated in the listing data gathered for this guide, so confirm them on the product page if you already own centers or a chuck you want to reuse.
Specs:
– Swing over bed: 8 inches
– Distance between centers: 13 inches
– Motor: 1/3 HP
– Speed control: Electronic variable speed, 750 to 3,200 RPM
– Spindle thread: not stated
– Headstock and tailstock taper: not stated
– Included accessories: Two tool rests, faceplate, spur center, and live center, as listed
– Faceplate size: not stated
See the Shop Fox W1704 on Amazon
WEN LA3421 Variable Speed Mini Lathe
The WEN LA3421 is the smallest and lightest machine here, an 8-inch by 13-inch mini lathe aimed squarely at pens, small bowls, and hobby turning on a crowded bench. Its 3.2-amp soft-start motor drives electronic variable speed from 750 to 3,200 RPM, so a pen blank and a small bowl can be turned back to back with a dial turn.
One detail separates it from the midi lathes above: the spindle and tailstock tapers are MT1, not MT2, and the spindle thread is 1 inch by 8 TPI. Pen mandrels and centers for this lathe must be MT1 versions, which WEN sells, but MT2 accessories from a bigger lathe will not seat.
WEN includes a 2.3-inch faceplate, an MT1 spur center, an MT1 live center, a knockout rod, and two interchangeable tool rests at 4-1/2 inches and 7 inches, plus a flat wrench. At 45 pounds with lever-style clamping, it sets up quickly and stores easily, making it a sensible first lathe for pen turning.
Specs:
– Swing over bed: 8 inches
– Distance between centers: 13 inches
– Motor: 3.2-amp, 120V, soft start
– Speed control: Electronic variable speed, 750 to 3,200 RPM
– Spindle thread: 1 inch x 8 TPI
– Headstock and tailstock taper: MT1
– Included accessories: 2.3-inch faceplate, MT1 spur center, MT1 live center, knockout rod, 4-1/2-inch and 7-inch tool rests, flat wrench
– Weight: 45 pounds
How to Choose
Start with swing over bed, because it caps the diameter of every bowl you will turn on the machine. An 8-inch swing limits bowls to roughly 7 inches finished, while a 12-inch or 12-1/2-inch swing opens up serving bowls and platters. Distance between centers matters for spindles: 13 inches handles pens and short spindles, while 18 to 20-1/2 inches covers most furniture parts.
Next, match the accessory standard. All five lathes here use a 1 inch by 8 TPI spindle thread where the maker states it, so chucks and faceplates interchange. Tapers differ: the JET, Delta, and WEN LA3424 use MT2 centers, the WEN LA3421 uses MT1, and the Shop Fox taper is not stated in its listing. Buying centers in the wrong taper is the most common first-lathe mistake.
Then decide how you want to change speeds. Electronic variable speed, fitted to the JET, Delta, Shop Fox, and WEN LA3421, lets you slow down for an unbalanced blank and speed up for a pen without stopping. Belt-step pulleys on the WEN LA3424 give five fixed speeds with simpler mechanics. Finally, anything over 100 pounds wants a dedicated bench.
Who Should Skip
Skip benchtop lathes entirely if you plan to turn bowls larger than about 12 inches across, long table legs, or architectural columns; that work needs a floor-standing lathe. Skip the mini lathes, the Shop Fox W1704 and WEN LA3421, if bowls are your main interest, because their 8-inch swing and lighter motors will frustrate you quickly.
Skip the WEN LA3421 if your existing centers, mandrels, or drill chucks are MT2, since its MT1 tapers will not accept them. And skip every model here if your bench cannot be bolted or weighted down: a benchtop lathe still vibrates with an out-of-round blank.
FAQ
What size lathe do I need for bowls?
The swing over bed sets the limit. A 12-inch or 12-1/2-inch swing, like the JET, Delta, and WEN LA3424 offer, turns bowls up to about 11 inches finished. An 8-inch mini lathe is limited to small bowls of roughly 7 inches.
Are MT1 and MT2 accessories interchangeable?
No. MT1 and MT2 are different taper sizes, so a center or mandrel made for one will not seat correctly in the other. The WEN LA3421 uses MT1 at both ends, while the JET, Delta, and WEN LA3424 use MT2.
Is variable speed worth it for pen turning?
Pens are small and balanced, so fixed speeds work, but variable speed lets you slow down for drilling and speed up for finishing without moving a belt. Four of the five lathes here include it; only the WEN LA3424 uses belt-step pulleys.
Can a benchtop lathe turn table legs?
Only short ones. Table legs usually run 28 to 30 inches, which exceeds the 13 to 20-1/2 inches between centers on these machines unless a bed extension is fitted. For regular leg work, choose a floor-standing lathe instead.
Final Verdict
For one lathe that covers bowls, pens, and spindle work in a small shop, the JET JWL-1221VS is the strongest all-round choice, with the Delta 46-460 close behind. The WEN LA3424 delivers midi capacity with simple belt-step speeds, the Shop Fox W1704 remains a proven compact starter, and the WEN LA3421 is the pick for pen turners who need variable speed in the smallest footprint.
Related guides
Read next
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.





Write Your Review
No reviews yet. Be the first to share your experience!