Table of Contents

14 sections 14 min read
Updated Nov 12, 2026· 13 min read

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

The short answer: the best bench dogs are the ones that fit your bench holes snugly, sit at the right height, and grip your workpiece without marring it. For most benches that means a set of round or square dogs matched to the hole size, paired with a vise or a row of holes that gives a useful span. Wood dogs are gentle on surfaces, metal dogs are durable, and spring-loaded or clamping designs add convenience. Fit matters far more than material or name.

This guide does not rank products or quote dimensions. It explains what bench dogs do, the main types, how to measure your holes, how to place them, and how to avoid the common mistakes that damage a bench or a project. Always check current listings and manufacturer instructions before ordering, and measure your own bench instead of trusting a generic description.

Contents
  1. Contents
  2. What Bench Dogs Actually Do
  3. The Main Types of Bench Dogs
  4. Wood, Brass, Steel and Plastic
  5. Measuring Your Holes and Getting a Good Fit
  6. Hole Layout, Height and Workholding
  7. Comparison Table: Dog Types
  8. Using Dogs for Common Tasks
  9. Making Your Own Dogs
  10. Safety and Workholding Care
  11. Buyer Checklist
  12. Mistakes to Avoid
  13. Frequently Asked Questions
  14. Bottom Line

Contents

What Bench Dogs Actually Do

A bench dog is a peg that sits in a hole in your workbench top and rises above the surface to act as a stop or a clamping point. Used with a vise, a tail vise or a second dog, it traps a board between two points without clamps cluttering the surface. The result is a flat, open bench where tools can travel across the work without bumping hardware.

Dogs shine at planing, sanding, scraping and chopping, where the force pushes the board in one direction. They are less suited to tasks that pull upward or twist the work, for which a holdfast, a clamp or a different jig is a better choice. Understanding that limit prevents most disappointments.

Dogs and vises work as a team

The dog itself is passive. Its power comes from the vise that closes against it. A bench with a dog hole row and a tail vise or a vise with dog holes in its jaw gives a long clamping range. A bench with only a shoulder vise and no holes limits how you can use the dogs.

The Main Types of Bench Dogs

Round dogs

Round dogs fit round holes, which are simple to drill with a brace or a drill and guide. They rotate, which means that the clamping face may not stay parallel to the work unless it is flattened or notched. Many designs include a flat face or a slot for this reason. They are common because the holes are easy to make.

Square dogs

Square or rectangular dogs sit in mortised holes that prevent rotation. The face stays aligned, which helps with parallel clamping, but the holes take more effort to cut. Square dogs are common on traditional European benches and on benches with a dedicated dog strip.

Spring-loaded dogs

These carry a leaf or coil that presses against the wall of the hole so that the dog stays at height until pushed down. They save fiddling when you want a dog to stay up or stay down, but the spring adds wear and a possible failure point. Check that the spring is secure and that the dog moves smoothly in your hole.

Clamping dogs

Some designs add a hook, a threaded arm or a lever that clamps to the work itself. They are useful for awkward shapes and for tasks where a plain stop is not enough. They tend to cost more and may need a particular hole size, so check compatibility.

Planing stops and low-profile dogs

A stop is a specialised dog with a low or toothed profile that sits below the work surface so that a plane can pass over it. It suits planing thin stock and keeps the cutter away from metal. Some woodworkers keep a separate low-profile set for this reason.

Holdfasts as a companion

A holdfast is not a dog, but it works in the same holes. A bent shaft that wedges in a hole and presses down on the work with a pad, it holds against downward and sideways forces. It complements dogs by covering the jobs that dogs cannot do, such as holding a board for chopping or sawing.

Wood, Brass, Steel and Plastic

Wood dogs

Hardwood dogs are soft enough to protect your workpiece and your plane irons, and they can be made or re-shaped easily. They also wear and can split along the grain, especially if the hole is oversize. Check the grain direction and the thickness of the shaft before you buy.

Brass and bronze dogs

Brass is gentle on tools relative to steel and does not rust. It is heavier, which can help a dog stay seated. Brass can still dent softwoods when overtightened, so a thin pad or a wood face makes sense for delicate surfaces.

Steel and iron dogs

Steel is strong and resists deformation under heavy clamping. The risk is that a plane iron can strike it and chip, and the metal may mark softer woods. Coatings can reduce rust but may wear with use. Use steel where durability matters more than gentleness.

Plastic and composite dogs

Moulded dogs are light and kind to surfaces. They suit light work but may flex under heavy pressure, so judge them by how you actually clamp.

Faces, pads and inserts

Look at the contact face. A smooth, slightly textured or padded face grips without marring. Replaceable pads or leather facings are a practical feature. Check whether the face is flat or curved, because a flat face holds better against a flat edge.

Measuring Your Holes and Getting a Good Fit

Fit is the leading cause of disappointment. A dog that rattles in its hole slips when pressure rises, while one that is too tight will not seat or can split the bench.

Measure the actual hole

Use calipers or a rule to measure the diameter or width of your hole at the top, in the middle and near the bottom. Holes drilled by hand are rarely perfectly uniform. Compare your readings with the stated shaft size, and note whether the manufacturer lists a tolerance.

Check depth and bench thickness

The dog needs enough shaft in the hole to stay upright under side pressure. Measure the top thickness and see how much of the shaft will sit within it. A thin bench top limits the length of the shaft, and a hole that goes through to a shelf or a stretcher may be blocked.

Hole shape and angle

Some holes are drilled at an angle to lean the dog toward the work, a trick that helps it bite as pressure increases. Confirm that your dogs will work in an angled hole, and measure the angle carefully before you buy.

Metric versus imperial

Hole sizes appear in both systems, and a small difference can matter. Read listings carefully to see which system they use, and avoid assuming that a nearly equal size will fit.

Hole Layout, Height and Workholding

Spacing along the bench

A row of holes with regular spacing gives flexibility. The distance between holes limits the lengths of board you can clamp without moving a dog, so closer spacing gives finer control. If you are planning a new row, consider your usual workpiece sizes.

Dog height

A dog should rise above the work enough to bear on its edge, but not so far that a plane or a hand strikes it. A short dog may only touch the bottom of a thick board, while a tall one gets in the way of thin stock. Adjustable or spring-loaded dogs offer a margin.

Placement relative to the vise

Position the dog row so that the clamping axis aligns with the vise screw, which reduces racking when you apply force. A clamp that pulls off axis can twist a board and make the dogs lose their grip.

Preventing the bench from taking damage

Overtightening can enlarge a hole or crush the fibres around it. Mild pressure generally suffices, and a snug fit with a good face is better than brute force.

Comparison Table: Dog Types

The table below describes general tendencies. Individual products vary, so use it to shortlist.

Type Hole needed Surface friendliness Strength Best for
Round hardwood Drilled round High Moderate General planing and sanding
Square hardwood Mortised square High Moderate to good Traditional benches with a dog strip
Round brass Drilled round Good Good Everyday use, lasting wear
Steel Round or square Lower High Heavy clamping
Spring-loaded Match the listing Varies Varies Quick height changes
Clamping Match the listing Varies Varies Odd shapes
Low-profile stop Match the listing Varies Moderate Planing thin stock

If you are unsure, begin with a pair or two of a style that matches your holes, then expand your set once you know which tasks you repeat.

Using Dogs for Common Tasks

Planing boards

Put a dog in the tail vise or a row hole, push the board against it and close the vise. Keep the board’s edge slightly lower than the top of the dog so that the plane clears it. Planing against the direction of the dog helps the work stay put.

Sanding and scraping

Dogs hold sheets and panels flat for sanding and scraping, which leaves the whole surface clear. Place a rag or pad between the dog and delicate surfaces.

Chopping and sawing

Heavy chopping or sawing often needs a holdfast or a clamp in addition to a dog, because vertical forces can lift the board. Do not rely on a dog alone for these jobs.

Gluing up panels

Dogs can help to align boards in a glue-up by holding them together while clamps go on. Do not let glue run into the holes, because dried glue can seize a dog in place.

Making Your Own Dogs

Many woodworkers turn or carve their own dogs from offcuts of dense hardwood. It is an inexpensive project that lets you match the hole exactly and shape the face as you like. Choose straight grain, orient it along the shaft and test the fit before you rely on the dog.

Safety and Workholding Care

Workholding failures usually happen when the work moves unexpectedly while a tool is in motion. Treat dogs as a convenience for light to moderate forces, and use a secure clamp or a different method when you are unsure.

  • Test the grip by pushing the workpiece gently before you start cutting, planing or chopping.
  • Keep your hands clear of the path of a plane, chisel or saw, and of the line a dog might travel if it releases.
  • Never rely on a dog to restrain work against a powered tool, such as a router or a power sander that can grab and throw the piece.
  • Use eye protection, since a dog or a workpiece that releases can send fragments toward your face.
  • Seat each dog fully before applying force, and make sure it cannot pop up through a worn hole.
  • Avoid hammering on a dog unless the manufacturer’s instructions say it is meant for that.
  • Keep holes clear of chips, glue and debris so that the dogs seat properly.
  • Inspect springs, faces and shafts for cracks or wear, and stop using any dog that looks damaged.

Follow current instructions from the maker of your bench, vise and dogs. Methods and recommended uses vary, so check what is stated for your specific equipment.

Buyer Checklist

  • Have I measured the hole width or diameter at several depths?
  • Do I know whether my holes are round, square or angled?
  • Is the shaft length suitable for my bench thickness?
  • Will the dog rise to a useful height without getting in the way?
  • Is the contact face friendly to my workpieces, and is it replaceable?
  • Does the material suit my work, in terms of strength and gentleness?
  • Do I need spring-loading, and have I checked how it behaves?
  • Is the listing in metric or imperial units, and do I know which my bench uses?
  • Do I own a vise or stop that completes the clamping span?
  • Do I need a holdfast or clamp for the jobs that dogs cannot do?
  • Is there a return option if the fit is wrong?
  • Have I read the current product details and instructions?

Mistakes to Avoid

Ordering without measuring

A near-fit dog is a loose dog. Measure first and compare with the listing.

Choosing steel for everything

Metal is strong, but it can mar workpieces and nick plane irons. Match the material to the task.

Over-tightening the vise

Excess force can spoil the hole, bend the dog or crush the board. Apply only what you need.

Expecting dogs to hold against lifting forces

Dogs resist forces along the clamping direction. For chopping and for work that tries to rise, add a holdfast or a clamp.

Ignoring height

A dog that sits too high gets in the way of a plane, and one that sits too low does nothing. Adjust or choose a more suitable size.

Trying to hold powered work with dogs

Power tools generate forces that can fling a loose piece. Use secure clamps and approved jigs.

Frequently Asked Questions

What size bench dog do I need?

It depends on the size of your holes. Measure the diameter or width carefully at several depths and compare with the stated shaft dimensions, remembering to check whether the listing is metric or imperial.

Are round or square bench dogs better?

Round dogs suit simple drilled holes, while square dogs resist rotation and keep their faces aligned. The better choice depends on your bench and how much effort you want to put into the holes.

Do wood bench dogs work as well as metal ones?

For many tasks they do, and they are kinder to surfaces and tools. Metal dogs tolerate heavier clamping. Many woodworkers keep both.

Can I use bench dogs without a vise?

You can use them with a second dog and a wedge or a clamp, but the pairing with a vise gives the most useful clamping range. A vise that matches your hole row works best.

What is the difference between a bench dog and a holdfast?

A dog acts as a stop or clamp point along the work. A holdfast wedges in a hole and presses down on the work, so it handles downward and sideways forces that a dog cannot.

How tall should a bench dog stand above the bench?

It should rise high enough to bear on the edge of the workpiece without interfering with tools. The right height depends on the thickness of your stock, so adjustable or spring-loaded types give a margin.

Can I drill holes in my bench for dogs?

Many people do. Plan the layout carefully, check what lies beneath the bench top, and test on a scrap first. If your bench is a manufactured product, review the maker’s guidance before altering it.

Why does my bench dog slip?

Usually the hole is oversized, the face is smooth, the clamping axis is off or the force is too high. Check the fit, add a face pad and align the dog with the vise screw.

Bottom Line

Match your dogs to your holes, choose a material that suits your work, and keep a holdfast or clamp for jobs dogs cannot manage. Start with a small set, learn which tasks you repeat and add more only when you see a gap. Treat workholding as a safety issue, test the grip before each operation and check current manufacturer instructions for your bench and vise.

When you are ready to compare options, you can browse round bench dogs, brass bench dogs, square bench dogs and workbench holdfasts, then check each against the list above.

Disclosure: As an Amazon Associate, we earn from qualifying purchases. Links marked as sponsored may earn us a commission at no extra cost to you.

F
FD Woodworking Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Bench Dogs: Types, Hole Sizes and Holdfast…Check price on Amazon

Related guides

Browse all Tools Workshop guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.