Updated Nov 21, 2026· 9 min read

Key takeaways

  • Five spline jigs for table saws and router tables, from compact right-angle clamps to full sled systems, compared for fit, capacity, and ease of setup.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

A mitered corner looks clean on a box or a picture frame, and a spline is what keeps it that way. The thin strip of hardwood set across the joint adds glue area, resists racking, and lines up the two faces so the corner closes flush. The hard part is cutting the slot: it must sit centered on the joint, square to the miter, and the same depth on every corner, or the spline shows unevenly.

Our top pick: Rockler Deluxe Spline Jig for Table Saw and Router Table. Runner-up: Woodpeckers Spline Jig for Dovetails and Miter Joints.

A spline jig takes that job out of the hand-held category. It holds the mitered workpiece at a fixed 45-degree angle while the blade or bit cuts across the joint, so each slot lands in the same place. The five jigs below cover the two main designs: full sled systems that ride in a miter slot, and compact right-angle clamps that hold the corner while a table saw or router does the cutting.

As an Amazon Associate, we earn from qualifying purchases.

Contents
  1. Quick answer
  2. The five spline jigs
  3. How to choose
  4. Who should skip
  5. FAQ
  6. Final verdict
  7. Product and ASIN Reference

Quick answer

For most shops, the Rockler Deluxe Spline Jig is the most versatile pick: a 45-degree sled that works on a table saw or a router table and cuts straight, angled, dovetail, and V-groove splines. Woodworkers who build wide frames will value the Woodpeckers SPLINE-23, while the compact right-angle clamps from YUCHENGTECH, Garosa, and TOOLCOOL suit smaller boxes and frames at a lower tier.

The five spline jigs

Rockler Deluxe Spline Jig for Table Saw and Router Table

The Rockler Deluxe is the full sled in this lineup, built around an adjustable 45-degree sled that holds the workpiece while the blade cuts across the miter. An aluminum miter bar with adjustable tension blocks rides in a standard miter slot, and two adjustable fences set the slot position so each corner matches the last. MDF zero-clearance inserts sit under the cut to keep tear-out down on visible faces.

It handles more than plain splines: the same setup cuts straight, angled, dovetail, and V-groove splines, which makes it a useful fixture for decorative boxes as well as plain frames. It mounts on a table saw or a router table, so it adapts to whichever machine is already set up. At 7.92 pounds it stays put during a cut without feeling like a fixed installation.

Specs

  • :
  • 45-degree adjustable sled with aluminum miter bar and tension blocks
  • Two adjustable fences and a miter stop for repeatable slot position
  • MDF zero-clearance inserts included
  • Cuts straight, angled, dovetail, and V-groove splines
  • Table saw and router table use
  • Weight: 7.92 pounds

Woodpeckers Spline Jig for Dovetails and Miter Joints

The Woodpeckers SPLINE-23 is the professional-grade pick, machined in the USA from aluminum and powder-coated steel. Two extruded aluminum Super Track sections carry four molded flip stops, and UHMW glide strips on the base and legs let the jig slide smoothly against the rip fence without marking the saw top. Laser-engraved scales on the tracks set the spline position against the blade or bit.

Capacity is its strong point. It handles frames from 0.5 inch to 16 inches wide, and moving the tracks inward extends that to pieces up to 3 feet wide, which covers tall casework and long frames that smaller jigs cannot reach. It also mounts on a router table for wider splines and dovetail keys. Assembly takes about 15 minutes, and the kit includes the glide strips, flip stops, angle brackets, legs, and hardware.

Specs

  • :
  • Two extruded aluminum Super Track sections with powder-coated steel legs
  • Four molded flip stops and laser-engraved scales
  • UHMW glide strips on base and legs
  • Frames 0.5 to 16 inches wide, up to 3 feet with tracks moved inward
  • Table saw and router table use
  • Made in USA

YUCHENGTECH Adjustable Spline Jig for Table Saw

The YUCHENGTECH jig is the budget pick in this lineup, a compact right-angle clamp machined from aerospace-grade anodized aluminum. It clamps frames from 5 to 42 mm thick and holds work up to 500 mm deep, with bidirectional clamping that steadies deep frames from both sides. A 1 mm ground clearance keeps the workpiece almost flush with the table, and the blade path is metal-free, so the blade never meets the jig.

At 2.84 pounds it moves easily between the table saw, the router table, and the planer, and it stores in a drawer when the job is done. It suits picture frames, small boxes, and custom art projects where a full sled would be more fixture than the work needs.

Specs

  • :
  • CNC-machined aerospace-grade anodized aluminum
  • Clamps stock 5 to 42 mm thick, frames up to 500 mm deep
  • 1 mm ground clearance with a metal-free blade path
  • Bidirectional clamping for deep frames
  • Table saw, router table, and planer use
  • Weight: 2.84 pounds

Garosa Table Saw Spline Clamp Aluminum Jig with Limiters

The Garosa is the heavy-duty clamp in this group, an aluminum alloy jig built around four built-in flip limiters that set spline alignment without remeasuring. UHMW slides on the bottom and edges lower friction and protect the machine table, and two height settings handle workpieces from 0.5 inch to 16 inches wide. It works on a table saw or a router table.

The single clamp unit weighs 1.95 kg, about 4.3 pounds, which gives it enough mass to stay steady while remaining easy to lift on and off the table. The flip limiters are the feature that sets it apart: once they are set, each corner is cut at the same offset, which is what keeps a four-sided frame square.

Specs

  • :
  • Aluminum alloy body with four built-in flip limiters
  • UHMW slides on bottom and edges
  • Two adjustable height settings
  • Workpieces 0.5 to 16 inches wide
  • Table saw and router table use
  • Weight: 1.95 kg (4.3 pounds)

TOOLCOOL Spline Jig for Table Saw and Router Table

The TOOLCOOL jig is a compact right-angle clamp in CNC-machined anodized aluminum, aimed at boxes and frames up to 20 inches wide. It clamps stock from 5 to 42 mm thick, and the design keeps metal clear of the blade or bit, with only 1 mm of clearance above the surface. An Allen wrench and a hex bit are included, so the jig can be driven by hand or with a drill.

It weighs 1.26 kg, about 2.78 pounds, and suits intermediate woodworkers who want a precise spline fixture without the footprint of a sled. The right-angle form also works for dovetail keyways, which makes it useful on decorative boxes where the spline is part of the look.

Specs

  • :
  • CNC-machined anodized aluminum alloy
  • Clamps stock 5 to 42 mm thick, project widths 0.6 to 20 inches
  • No metal above the blade or bit, 1 mm ground clearance
  • Allen wrench and hex bit included
  • Table saw and router table use
  • Weight: 1.26 kg (2.78 pounds)

How to choose

Match the jig to the work first. A sled system such as the Rockler Deluxe or the Woodpeckers SPLINE-23 suits repeated frame and box work, because the miter bar and fences hold position from one corner to the next. A right-angle clamp such as the YUCHENGTECH, Garosa, or TOOLCOOL suits smaller jobs and tight shops, because it clamps the corner and stores in a drawer.

Check width capacity against the largest frame you build. The Woodpeckers jig reaches 16 inches wide and 3 feet with its tracks moved inward, the Garosa reaches 16 inches, and the TOOLCOOL reaches 20 inches of project width. The compact clamps hold stock from 5 to 42 mm thick, which covers most frame and box stock.

Look at the machine you will use. All five jigs work on a table saw, and all but the planer-focused YUCHENGTECH also work on a router table, which matters for wider splines and dovetail keys. Flip stops and limiters, found on the Woodpeckers and Garosa jigs, save setup time when every corner of a frame must match. Zero-clearance inserts, included with the Rockler, keep tear-out down on faces that will stay visible.

Who should skip

A spline jig is not for every shop. If you build one picture frame a year, a shop-made 45-degree sled from scrap plywood does the same job with a little more setup time, and it fits odd sizes a fixed jig cannot. If you have no table saw or router table, none of these jigs has a machine to run on, and a hand-held router with an edge guide is the better route.

Very wide casework is also a limit. The Woodpeckers jig reaches 3 feet with its tracks moved inward, but a full-height cabinet corner is beyond every jig here, and a shop-made cradle sized to the piece is the practical answer. Finally, if your joints are already cut and glued, a spline jig cannot help: the slot must be cut while the miter is still open.

FAQ

What is a spline jig used for?

A spline jig holds a mitered workpiece at 45 degrees while a table saw blade or router bit cuts a slot across the joint, so a hardwood spline can be glued in to strengthen and align the corner.

Can a spline jig work on a router table?

Yes, most of them can. The Rockler Deluxe, Woodpeckers SPLINE-23, Garosa, and TOOLCOOL jigs all mount on a router table as well as a table saw, which suits wider splines and dovetail keys.

What thickness of stock can these jigs hold?

The compact right-angle clamps hold stock from 5 to 42 mm thick. The sled systems handle a wider range of frame widths, with the Woodpeckers jig reaching 16 inches wide and 3 feet with its tracks moved inward.

Do I need a spline jig for picture frames?

A jig helps, but it is not required. A shop-made 45-degree sled works for occasional frames, while a dedicated jig earns its place when you cut the same slot on many frames and want every corner to match.

Final verdict

The Rockler Deluxe Spline Jig is the most versatile pick for a general shop, with a sled that covers straight, angled, dovetail, and V-groove splines on a table saw or a router table. The Woodpeckers SPLINE-23 is the professional-grade choice for wide frames and casework, with the largest capacity here. For smaller boxes and frames, the Garosa clamp offers the most repeatable setup through its flip limiters, while the YUCHENGTECH and TOOLCOOL clamps give the same right-angle format at a budget tier. Pick by the size of the work and the machine you already own, and the spline slots will land where they belong.

Product and ASIN Reference

Product ASIN
Rockler Deluxe Spline Jig for Table Saw and Router Table B0GZX2ZTGB
Woodpeckers Spline Jig for Dovetails and Miter Joints B0C7LDYL2W
Yuchengtech Adjustable Spline Jig for Table Saw B0F2MQNGVR
Garosa Table Saw Spline Clamp Aluminum Jig with Limiters B0CW5Z866H
TOOLCOOL Spline Jig for Table Saw and Router Table B0D5D16FB4
F
FD Woodworking Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Spline Jigs for Strong Mitered Woodworking JointsCheck price on Amazon

Related guides

Browse all Buying Guides guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.