Key takeaways
- Ingersoll Rand 23474661 pressure switch is an OEM replacement for SS3L3, SS4L5, and SS5L5 N5 compressors, for owners restoring correct cycling.
What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Uncategorized › Ingersoll Rand 23474661 Pressure Switch Review Guide
The Ingersoll Rand 23474661 pressure switch is an OEM replacement part for owners of compatible Ingersoll Rand air compressors whose machines no longer start and stop at the right points in the pressure cycle. A pressure switch is a small component with an outsized job: it senses tank pressure and tells the motor when to run and when to rest. When it fails, a compressor may refuse to start, run on too long, or cycle in a way that makes workshop work frustrating and uncertain.
This review is for woodworkers and other shop users who rely on a compressor for nailers and finishing work. It covers what this OEM switch is for, how to confirm fit, and when replacement makes sense.
As an Amazon Associate, we earn from qualifying purchases.
Contents
Quick answer
The Ingersoll Rand 23474661 pressure switch is an OEM replacement for SS3L3, SS4L5, and SS5L5 N5 air compressors. It suits owners whose switch is faulty and who want a factory part matched to those models. Confirm the model and part number before ordering, and skip it if your compressor is a different model or the fault lies elsewhere.
Key specs
| Spec | Detail |
|---|---|
| Brand | Ingersoll Rand |
| Part number | 23474661 |
| Part type | Pressure switch |
| Part status | OEM part |
| Equipment type | Air compressor |
| Compatible model listed | SS3L3 |
| Compatible model listed | SS4L5 |
| Compatible models listed | SS5L5 and N5 |
Design and everyday use
In daily shop use, a healthy pressure switch is almost invisible. The compressor fills the tank, cuts out at its upper pressure, and stays quiet while you work. As tank pressure falls to the cut in point, the motor restarts. That rhythm lets nailers and blow guns work without the operator thinking about the machine.
The 23474661 is the control point for that rhythm on the listed models. Choosing the OEM part matters because a switch must suit the demands of the specific compressor it serves. A factory part removes guesswork about fit that can come with a generic substitute chosen only by appearance. Two switches can look alike while behaving differently in service.
Replacement is a job for a careful owner or a technician who follows the compressor manual. Power must be isolated, tank pressure released, and wiring noted before anything is removed. Photographing connections first prevents confusion later. After fitting, check the machine through a full fill and draw down cycle.
Safety deserves plain language. A compressor combines stored pressure, electrical supply, and automatic starting. If any part of the job is unclear, professional service is the right choice. Never bypass a pressure switch to keep a compressor running. The switch keeps the machine operating inside its intended cycle.
Once fitted, everyday care is mostly observation. Listen for normal cycling, watch for leaks, and note changes such as rapid short cycling. Those symptoms can also point to leaks or other controls, so diagnose rather than assume. Keeping the area clean and dry helps in a dusty shop.
Who it’s for / who should skip
This part is for owners of an Ingersoll Rand SS3L3, SS4L5, or SS5L5 N5 compressor who have identified the pressure switch as faulty and want the OEM replacement, part 23474661. It suits home workshops, small joinery shops, and maintenance benches where the compressor is a known machine worth keeping in service rather than replacing outright.
Skip it if your compressor model is not one of the listed models. Similar appearance is not compatibility. Skip it also if troubleshooting has not yet isolated the fault. A compressor that will not start may have a power supply, motor, capacitor, or wiring problem, and replacing the switch alone will not cure those. If pressure readings themselves are in doubt, verify the gauge and check for air leaks first. Finally, skip a self installation if you are not confident working with electrical connections and stored pressure. Paying a technician is wiser than risking an incorrect repair.
How it compares with alternatives
Compared with a generic aftermarket pressure switch, this OEM part offers model specific confidence. A generic switch may be adjustable and may suit several machines, but it places the burden on the buyer to confirm pressure settings, electrical suitability, and connection layout. The Ingersoll Rand part is identified for the listed compressors, which simplifies the decision for an owner who wants the factory route.
Compared with replacing the whole compressor, fitting a new pressure switch is the focused repair when the tank, pump, and motor remain sound. A new machine may be justified when several major parts are worn, but it is a large response to a single failed control. Replacing the switch preserves a familiar machine, its fittings, and its place in the workshop layout.
Compared with temporary workarounds, a correct replacement gives a clear outcome. Once the switch is confirmed as the fault, further patching wastes shop time and can create safety concerns. Diagnose, confirm the model, fit the correct part, and test a full cycle.
FAQ
Which compressors does the 23474661 pressure switch fit?
It is listed for Ingersoll Rand SS3L3, SS4L5, and SS5L5 N5 air compressors. Check the model identification on your own machine and compare the part number before ordering, because a similar looking compressor may use a different switch.
What does an air compressor pressure switch do?
It senses tank pressure and controls the motor. When pressure falls to the cut in point, the switch starts the motor. When pressure reaches the cut out point, it stops the motor until air is used again.
Is this an original Ingersoll Rand part?
Yes. The 23474661 is described as an OEM part, the original equipment manufacturer part for the listed application rather than a generic substitute. That is the main reason owners choose it.
Should a workshop owner fit the switch personally?
Only if the owner is confident, follows the manual, isolates power, and releases tank pressure first. Anyone unsure about electrical work or stored pressure should use a qualified technician instead.
Final verdict
The Ingersoll Rand 23474661 pressure switch is the right kind of purchase when the diagnosis is clear and the compressor is one of the listed models. As an OEM part, it offers the fit and intended function that a generic substitute cannot promise in the same way. Confirm SS3L3, SS4L5, or SS5L5 N5 compatibility, fit it safely or use a technician, and test the full cycle afterward. Done that way, it is a focused repair that returns a trusted shop compressor to normal work.
Related guides
Read next
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.

Write Your Review
No reviews yet. Be the first to share your experience!