Updated Nov 21, 2026· 9 min read

Key takeaways

  • Compare the best transfer punch sets for woodworking layout, from fractional and metric sets to wire gauge and letter sizes, with specs for each pick.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

A transfer punch copies the exact position of an existing hole onto the workpiece beneath it. You slide the punch body into a hole in a hinge leaf, bracket, jig, or template, tap the top, and the small centered point on the tip leaves a precise mark for drilling. For woodworkers, that one move removes the measuring, marking, and re-measuring that usually goes into mounting hardware, copying a template, or matching holes between two parts of a build.

Our top pick: HHIP 28-Piece Transfer Punch Set, 3/32 to 1/2 Inch. Runner-up: HHIP 25-Piece Metric Transfer Punch Set, 1 to 13 mm.

The sets below all come from the HHIP line, which is the deepest transfer punch catalog sold on Amazon, and together they cover the five sizing systems a shop is likely to meet. The main fractional set handles everyday hardware work, the metric set covers imported fittings, and the large fractional, wire gauge, and letter sets fill in the sizes in between. Each set shares the same basic recipe of heat-treated tool steel, a black oxide finish, and punches ground slightly undersize so they slip into the guide hole and self-center before the tap.

As an Amazon Associate, we earn from qualifying purchases.

Contents
  1. Quick answer
  2. The picks
  3. How to choose
  4. Who should skip
  5. FAQ
  6. Final verdict
  7. Product and ASIN Reference

Quick answer

For most woodworking shops, the HHIP 8600-0041 28-piece fractional set is the one to buy first, since its 3/32 to 1/2 inch range covers common hinge, bracket, and jig holes. Choose the 8600-0043 metric set for millimetre hardware, the 8600-0411 for holes above 1/2 inch, and the wire gauge or letter sets for drill-size matching.

The picks

HHIP 8600-0041 28-Piece Transfer Punch Set

This is the core set for a woodworking shop and the natural budget-tier pick of the group. Its 28 punches run from 3/32 inch to 1/2 inch by 64ths, with a 17/32 inch punch added at the top of the range, which covers the hole sizes found in most butt hinges, shelf supports, corner brackets, and shop-made drilling jigs. Each punch is ground 0.0025 inch undersize, so the body slides into the guide hole without binding while the centered point still lands in the middle of the opening.

The punches are hardened tool steel with a black oxide finish, and at 4-7/8 inches long they give you room to hold the body steady while the workpiece and template stay clamped together. A metal indexed stand keeps every size in order, which matters more than it sounds when you are swapping between two close sizes at the bench. If you only transfer holes in fractional hardware, this set is the complete answer.

Specs

    • Pieces: 28
    • Sizes: 3/32 to 1/2 inch by 64ths, plus 17/32 inch
    • Fit: ground 0.0025 inch undersize
    • Material: hardened tool steel
    • Finish: black oxide
    • Punch length: 4-7/8 inches
    • Storage: metal indexed stand

    HHIP 8600-0043 25-Piece Metric Transfer Punch Set

    European hinges, drawer slides, and flat-pack fittings are drilled in millimetres, and a fractional punch sitting loose in a metric hole marks off center. This 25-piece set covers 1 to 13 mm in 0.5 mm steps, which matches the pilot and clearance holes used by the metric hardware a woodworker is most likely to copy onto doors, drawer boxes, and cabinet sides.

    The construction follows the same pattern as the rest of the line: heat-treated tempered tool steel, a black oxide finish, and 4-7/8 inch punch length, with an indexed stand included for storage. Shops that build with both hardware systems usually keep this set beside the fractional one rather than treating it as a replacement, because the two ranges overlap in coverage but not in exact fit. It sits in the mid-range tier and earns its place the first time a metric hinge cup or slide hole has to land exactly where the fitting puts it.

    Specs

      • Pieces: 25
      • Sizes: 1 to 13 mm in 0.5 mm steps
      • Material: heat-treated tempered tool steel
      • Finish: black oxide
      • Punch length: 4-7/8 inches
      • Storage: indexed stand
      • Manufacturer: ABS Import Tools Inc.

      HHIP 8600-0411 33-Piece Transfer Punch Set

      The small fractional set tops out at 17/32 inch, and this 33-piece set picks up exactly where it leaves off, running from 1/2 inch to 1 inch by 64ths. That range covers the larger holes in workbench hardware, bed fittings, heavy brackets, router template guides, and the boring patterns used on shop-built jigs, where a loose-fitting smaller punch would wander and mark off center.

      Like the 28-piece set, each punch is ground 0.0025 inch undersize for a slip fit in the guide hole, and the steel is heat-treated and tempered with a black oxide finish. The set ships with an indexed stand, and the larger diameters make it the premium-tier option of this group simply because of the ground it covers. Pair it with the 8600-0041 and a shop has continuous fractional coverage from 3/32 inch all the way to 1 inch, with no gap at the sizes in between.

      Specs

        • Pieces: 33
        • Sizes: 1/2 to 1 inch by 64ths
        • Fit: ground 0.0025 inch undersize
        • Material: heat-treated tempered tool steel
        • Finish: black oxide
        • Storage: indexed stand
        • Package dimensions: 12 x 8 x 8 inches

        HHIP 8600-0045 60-Piece Transfer Punch Set

        Wire gauge sizes exist because drill sizes do not always land on tidy fractions, and this 60-piece set covers the full number range from No. 1 to No. 60. In a woodworking shop it earns its keep when a hole has to match a specific drill size for a threaded insert, a machine screw clearance, or a replacement part whose hole was drilled to a numbered bit, since the punch that matches the drill also matches the hole it made.

        Each punch is 4-7/8 inches long, made from heat-treated tempered tool steel with a black oxide finish, and ground undersize so it seats in the guide hole before the tap. HHIP positions the set for transferring threaded, drilled, and tapped holes, which is exactly the situation when hardware is being moved from one part to another and the new hole must register with the old one. It is a mid-range tier set that solves a narrow problem very completely.

        Specs

          • Pieces: 60
          • Sizes: wire gauge No. 1 to No. 60
          • Material: heat-treated tempered tool steel
          • Finish: black oxide
          • Punch length: 4-7/8 inches
          • Fit: undersize for a precise fit in the guide hole
          • Intended use: transferring threaded, drilled, and tapped holes

          HHIP 8600-0044 25-Piece Letter Transfer Punch Set

          Letter sizes fill the remaining gaps in the drill index, sitting between the fractional and wire gauge steps, and this 25-piece set covers the full A to Z range. Letter drills are common tap and clearance sizes in mixed wood-and-metal shops, so a hinge, insert, or fitting drilled with a letter bit can be copied onto the mating part with the matching letter punch instead of a near-size fractional one that fits loosely.

          The set follows the same build as the wire gauge version: 4-7/8 inch punches in heat-treated tempered tool steel, black oxide finish, and an undersize grind for a precise fit in threaded, drilled, and tapped holes. Most woodworkers will reach for this set less often than the fractional one, but when a hole was made with a letter drill, nothing else in the drawer marks its position as faithfully. It is a mid-range tier companion to the fractional and metric sets rather than a first purchase.

          Specs

            • Pieces: 25
            • Sizes: letter sizes A to Z
            • Material: heat-treated tempered tool steel
            • Finish: black oxide
            • Punch length: 4-7/8 inches
            • Fit: undersize for a precise fit in the guide hole
            • Intended use: transferring threaded, drilled, and tapped holes

            How to choose

            Begin with the sizing system your hardware uses. Fractional sets cover most North American hinges, brackets, and jigs; metric sets match European fittings; wire gauge and letter sets match holes drilled to numbered and lettered bits, which show up around threaded inserts, machine screws, and older hardware. Many shops end up owning the fractional set plus one specialist set rather than a single large one.

            Next, check the fit. Transfer punches are ground slightly undersize, 0.0025 inch on the fractional sets here, so the body enters the guide hole freely while the point stays centered. A punch that matches the hole size on paper but is not undersize will bind or sit off center. Length matters as well: the 4-7/8 inch bodies in these sets leave enough punch above the template to hold and tap comfortably. Finally, look for an indexed stand, because a set whose sizes stay in order gets used, while loose punches in a drawer get measured one by one.

            Who should skip

            If you only mount hardware once in a while, a center punch and a careful layout with a marking knife will get the job done, and a full set will sit unused. Woodworkers who drill everything from digital templates or a CNC have no guide holes to copy from, so transfer punches add nothing. And if your work only ever involves one or two hole sizes, single punches in those sizes make more sense than any set here.

            FAQ

            What is a transfer punch used for in woodworking?

            It copies the position of an existing hole onto the part beneath it. The punch body slides into a hole in a hinge, bracket, jig, or template, and a light hammer tap drives the centered point into the workpiece, leaving an exact drilling mark with no measuring involved.

            How is a transfer punch different from a center punch?

            A center punch has a plain pointed tip and marks wherever you place it, so its accuracy depends on your layout lines. A transfer punch has a body sized to a specific hole with a small centered point, so the guide hole itself positions the mark and the two holes register with each other.

            Which sizing system should a woodworker choose first?

            Fractional, in most cases, because common hinges, brackets, and shop jigs are drilled in fractional inches. Add the metric set if you fit European hinges or slides, and the wire gauge or letter sets when you need to match holes made by numbered or lettered drill bits.

            How do you use a transfer punch without damaging the point?

            Clamp the template or hardware firmly over the workpiece, seat the punch fully in the guide hole, hold it upright, and use one light tap rather than a heavy blow. The point only needs to dimple the surface for a drill bit to follow, and striking too hard can bend the tip or shift the template.

            Final verdict

            The HHIP 8600-0041 is the set most woodworkers should buy first: its fractional range, undersize grind, and indexed stand cover everyday hardware layout in one purchase. Add the 8600-0043 when metric fittings enter the shop, the 8600-0411 for holes above 1/2 inch, and the wire gauge and letter sets when matching drill-specific holes becomes part of the work. Together they form a complete transfer system built on one consistent pattern of steel, finish, and fit.

            Product and ASIN Reference

            Name ASIN
            HHIP 28-Piece Transfer Punch Set, 3/32 to 1/2 Inch B01ADBNEJE
            HHIP 25-Piece Metric Transfer Punch Set, 1 to 13 mm B0973MPLNF
            HHIP 33-Piece Transfer Punch Set, 1/2 to 1 Inch B01ADBO2AO
            HHIP 60-Piece Transfer Punch Set, No. 1 to 60 B0B1QS8NVH
            HHIP 25-Piece Letter Transfer Punch Set, A to Z B0B1QSYNRM
            F
            FD Woodworking Editorial Team
            We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
            Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
            Best Transfer Punch Sets for Accurate Hole Layout…Check price on Amazon

            Related guides

            Browse all Buying Guides guides →

            More from Amazon

            Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

            Amazon Business

            A free business account with business pricing and bulk-buying tools for work, shop or home office.

            Create a business account
            Amazon Prime

            Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

            Start a Prime free trial
            Audible

            Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

            Try Audible free
            Amazon Music Unlimited

            Ad-free music streaming. Eligible new subscribers can start with a free trial.

            Try Music Unlimited free

            As an Amazon Associate we earn from qualifying purchases.