Key takeaways
- Five replacement drill press chucks for woodworking, keyed and keyless, in JT33 and MT2 mounts, with capacity, fit and runout guidance for each pick.
What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Buying Guides › Best Drill Press Chucks: Keyed and Keyless Picks for 2026
A worn drill press chuck gives itself away in small ways. Bits wander off the layout line, jaws grip unevenly, a key rounds over in its socket, and runout turns a clean brad-point hole into an oval. The press itself usually has years of life left in it, and the chuck is the wear part that decides how true it drills. Swapping in a fresh chuck is a short job once you know which taper mount your spindle uses.
This roundup covers five replacement chucks for woodworking drill presses, from two keyless models built for fast bit changes to three keyed models built for maximum grip. Mounts cover the common JT33 nose and MT2 arbor patterns, and capacities run from fine 1/32 inch work up to full 5/8 inch shanks. Each pick lists its mount, capacity and construction, so you can match it to your spindle before you order.
As an Amazon Associate, we earn from qualifying purchases.
Contents
Quick answer
For most woodworkers, the WEN DPA167H is the pick: a heavy duty keyless chuck on the common JT33 mount with a wide 1/64 to 5/8 inch capacity. Choose the Llambrich JK-16 J33 for a premium medium duty keyless upgrade, and a keyed model such as the WEN LA164K when a press has an MT2 spindle socket.
The best drill press chucks
The five chucks below split into two keyless JT33 models, one keyed JT33 model, and two keyed chucks sold with MT2 arbors.
Llambrich JK-16 J33 Keyless Drill Chuck
Llambrich builds chucks in Spain for the machining trade, and the JK-16 J33 is its medium duty keyless model in the size most woodworking presses use. The three jaws close by hand, and grip firms up under drilling load, so there is no key to keep track of and no loose key to leave sitting in the chuck. Its 1/8 to 5/8 inch capacity covers the brad-point, twist and Forstner bits a woodworking press handles daily, while the slim 2-1/64 inch body keeps the work visible on small parts. The JT33 socket seats on any JT33 spindle nose or JT33 arbor. Runout discipline is the point of the JK line, and the taper seat is machined to sit squarely on a clean spindle nose. Choose it as the premium pick when the press is a long-term keeper and the chuck is the weak link.
Specs
- Type: Keyless, three-jaw
- Capacity: 1/8 to 5/8 in
- Mount: JT33 Jacobs taper
- Body diameter: 2-1/64 in
- Model: JK-16 J33
- Maker: EuroLink (Llambrich)
WEN DPA167H Keyless Drill Press Chuck
The DPA167H is the straightforward keyless upgrade for the many benchtop and floor presses built around a JT33 spindle nose. It opens and closes by hand, and its 1/64 to 5/8 inch capacity is the widest in this roundup, holding fine bits that slip in coarser chucks as well as full 5/8 inch shanks. WEN builds it as a heavy duty model, and it mounts straight onto a JT33 nose or a JT33 arbor with no extra hardware in the box to lose. For a press that swaps between pilot holes, brad-points and Forstner bits all day, this is the low-fuss route to a true-running front end. It is also the natural replacement for the keyless chucks WEN fits to its own presses, and it suits any other brand with the same taper.
Specs
- Type: Keyless, three-jaw, heavy duty
- Capacity: 1/64 to 5/8 in
- Mount: JT33 Jacobs taper
- Model: DPA167H
- Arbor: Not included
WEN LA164K Keyed Drill Chuck with MT2 Arbor
The LA164K pairs a 5/8 inch keyed chuck with a tanged MT2 arbor, which suits presses whose spindle takes a removable Morse taper arbor rather than a fixed nose. The chuck is machined from chromium vanadium steel and closes with the included key, giving a firm bite on smooth shanks that can creep in a hand-tightened chuck. The arbor tang seats in the spindle slot, so a drift key knocks the assembly out cleanly when it has to come off. WEN lists fitment for its 4214 and 4225 drill presses among other machines, but any MT2 socket is a candidate. Keyed grip earns its place with large Forstner bits and hole saws that load a chuck hard. This is the mid-range pick for owners who value clamping force over change speed.
Specs
- Type: Keyed, three-jaw, key included
- Capacity: Up to 5/8 in
- Arbor: MT2 Morse taper, tanged, included
- Material: Chromium vanadium steel
- Item weight: 1.11 kg
- Model: LA164K
HFS Keyed Drill Chuck JT33 (DRC-0102-JT33)
HFS sells this keyed chuck under part number DRC-0102-JT33, a compact 1/32 to 1/2 inch model on the JT33 mount, and it ships with its chuck key. The half-inch ceiling matches the smaller benchtop presses it targets, which rarely turn anything larger, and the compact body keeps the jaws close to the work when short bits are in use. At 680 grams it is the lightest pick here, a point in its favor on presses with light quills and small motors. The keyed pinion lets you snug the jaws down hard and evenly. For a hobby press that drills pen blanks, dowel holes and hardware pilots, the capacity ceiling is rarely a limit in practice. It is the budget route back to a true-running chuck for a small press.
Specs
- Type: Keyed, three-jaw, key included
- Capacity: 1/32 to 1/2 in (1 to 13 mm)
- Mount: JT33 Jacobs taper
- Part number: DRC-0102-JT33
- Item weight: 680 g
VINWOX Keyed Drill Chuck with MT2-JT3 Arbor
VINWOX builds this heavy duty keyed chuck from alloy steel and bundles it with an MT2 to JT3 arbor, so the chuck rides on a JT3 taper while the arbor handles the MT2 side of the spindle. Listed capacity is 0.63 inch, a shade over 5/8, and the assembly weighs 1.11 kilograms, which gives a big chuck the planted feel that helps it run true. The maker pitches it at drill presses and lathes for boring, pen blank drilling and trimming work, and notes plainly that it is not a chuck for handheld drills. The geared key drive and rigid construction suit repeated heavy cuts in hardwood and sheet goods alike. Choose it when you want a keyed chuck and its arbor supplied as one matched set.
Specs
- Type: Keyed, three-jaw, heavy duty
- Capacity: 0.63 in
- Arbor: MT2 to JT3, included
- Material: Alloy steel
- Item weight: 1.11 kg
- Model: VIN-DC0508JT3
How to choose
Match the mount before anything else. Drill press chucks attach in two ways. Many presses carry a fixed Jacobs taper nose, most often JT33, and the chuck presses straight onto it. Others take a removable arbor: a Morse taper, usually MT2, seats in the spindle while a Jacobs taper on the lower end of the arbor carries the chuck. The manual or spec plate names the taper, and a chuck knocked off with a pair of wedges, or an arbor drifted out of the spindle, settles the question in the shop. A JT33 chuck cannot fit a JT6 or JT3 nose, so read the taper before ordering anything.
Keyed or keyless. Keyless chucks open and close by hand and speed up bit changes, which matters when one job cycles through pilot, clearance and countersink bits. Keyed chucks clamp harder and hold smooth shanks more surely under heavy torque, which matters with large Forstner bits, hole saws and fly cutters. Neither style is stronger by mount: both rely on the same taper seat.
Capacity at both ends. The headline figure is the largest shank, 1/2 or 5/8 inch on the picks here. The small end matters too: a chuck that only closes to 1/8 inch cannot hold the fine bits used for hinge pilots and small work, while the DPA167H closes to 1/64 inch. Match the range to the bits you own.
Runout and seating. A new chuck only runs as true as its seat. Clean the taper nose or arbor and the chuck socket to bare metal, then seat the chuck with a firm tap from a mallet on a wood block. Dirt or a burr on the taper shows up as wobble that no chuck can correct, and a bent spindle defeats even the best chuck.
Who should skip
Skip this roundup if your press has a threaded spindle nose, since every pick here is a taper mount and none will thread on. Skip it, too, if the wobble lives in the machine itself: a bent spindle, worn quill bearings or a loose table call for repair work, and a fresh chuck will faithfully reproduce the fault. Owners of handheld drills and impact drivers need threaded or hex-shank chucks, a different family entirely. And if your work needs shanks beyond 5/8 inch, the answer is a larger press with an MT3 spindle, not a bigger chuck on an MT2 machine.
Frequently asked questions
How do I know whether my drill press takes a JT33 chuck or an MT2 arbor?
The manual or the spec plate on the head names the spindle taper. In the shop, drift the arbor out with a drift key through the quill slot: if an arbor comes out, the spindle side is a Morse taper. If the chuck alone knocks off a fixed nose with wedges, that nose carries the Jacobs taper, most often JT33 on woodworking presses.
Can I fit a keyless chuck where a keyed chuck was fitted before?
Yes, as long as the mount matches. Tightening style and mount are separate choices, so a keyless JT33 chuck seats on the same nose or arbor as a keyed JT33 chuck. The swap takes minutes: knock the old chuck off, clean the taper, and seat the new one.
Why does a brand new chuck still wobble?
Usually the seat, not the chuck. A speck of grit, a raised burr or dried oil on the taper holds the socket slightly crooked, and the error shows at the bit. Clean both tapers to bare metal and reseat with a firm tap. If wobble survives a clean seat, check the spindle itself for bend or bearing play.
What capacity should a woodworking drill press chuck have?
A 1/2 inch chuck covers most woodworking bits, and a 5/8 inch chuck adds room for the largest Forstner bits and hole saws. Check the small end as well: fine pilot bits need a chuck that closes near 1/32 inch or below. Buy for the bits you own, not the biggest number on the box.
Final verdict
Match the mount first, then pick your tightening style. For most woodworkers the WEN DPA167H is the default: keyless, JT33, and the widest capacity here. The Llambrich JK-16 J33 is the premium step up for a press that earns its floor space. If your spindle takes an arbor, the keyed WEN LA164K and VINWOX sets clamp hardest, and the compact HFS chuck puts a small benchtop press back in true order on a budget. Any of the five beats nursing a worn chuck through another project.
Product and ASIN Reference
| Product | ASIN |
|---|---|
| Llambrich JK-16 J33 Keyless Drill Chuck | B007R62FDK |
| WEN DPA167H Keyless Drill Press Chuck | B08R7V5B19 |
| WEN LA164K Keyed Drill Chuck with MT2 Arbor | B08FBKQPJX |
| HFS Keyed Drill Chuck JT33 DRC-0102-JT33 | B07G43354X |
| VINWOX Keyed Drill Chuck with MT2-JT3 Arbor | B0DT7T14WL |
Related guides
Read next
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.





Write Your Review
No reviews yet. Be the first to share your experience!