Updated Nov 20, 2026· 11 min read

Key takeaways

  • Compare five holdfasts and dog hole clamps on published specs: shaft diameter, reach, material, pads and pack counts for 3/4 inch and 20mm bench holes.

As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.

⭐ Key Takeaways
Quick answer: Our top pick is Narex Hot Forged Workbench Holdfast, with POWERTEC 71528 8-Inch Workbench Holdfast as a strong alternative.

A holdfast is the fastest way to pin a board to a workbench: drop the shaft into a dog hole, tap the top with a mallet, and the workpiece stays put for planing, routing, sanding or sawing. Tap the back of the arm and it releases just as quickly. The five picks below cover the main buying options, from a hot forged steel holdfast in the traditional pattern to cast iron pairs and a quick-acting cam clamp for 20mm MFT-style holes. For most benches with 3/4 inch dog holes, the Pony Jorgensen 1708 pair and the POWERTEC 71528 pair are the straightforward mid-range choices, the Narex is the premium forged option, and the IMPRESA three-pack and RUIITEN cam clamps fill the budget tier. Every figure in this guide comes from published listing and maker specifications, so the reach, shaft size and pack count you see are the numbers the makers themselves publish.

As an Amazon Associate, we earn from qualifying purchases.

Contents
  1. Table of Contents
  2. How These Holdfasts Were Compared
  3. Narex Hot Forged Workbench Holdfast
  4. Pony Jorgensen 1708 Bench Hold-Down Clamp
  5. POWERTEC 71528 8-Inch Workbench Holdfast
  6. IMPRESA Holdfast Dog-Hole Clamps, Pack of 3
  7. RUIITEN 2 Pack MFT Bench Holdfast
  8. How to Choose the Right Holdfast
  9. Frequently Asked Questions
  10. Conclusion

Table of Contents

  • How These Holdfasts Were Compared
  • Narex Hot Forged Workbench Holdfast
  • Pony Jorgensen 1708 Bench Hold-Down Clamp
  • POWERTEC 71528 8-Inch Workbench Holdfast
  • IMPRESA Holdfast Dog-Hole Clamps, Pack of 3
  • RUIITEN 2 Pack MFT Bench Holdfast
  • How to Choose the Right Holdfast
  • Frequently Asked Questions
  • Conclusion
  • Product and ASIN Reference

How These Holdfasts Were Compared

Holdfasts look simple, and that makes the published specifications more important, not less. The comparison below rests on the dimensions and construction details each maker publishes: shaft diameter, the dog hole size the tool is built for, reach from the shaft to the tip of the arm, body material and finish, whether a protective pad is included, and how many clamps come in the pack. Those six points decide whether a holdfast seats properly in your bench, how much of the board it can cover, and how it treats finished surfaces.

Two clamping styles appear in the lineup. Traditional holdfasts, including the Narex, Pony, POWERTEC and IMPRESA picks, lock by friction when the shaft cants in the hole under a mallet tap. The RUIITEN pick works differently: it is a quick-acting cam clamp with three pressure levels that suits 20mm holes in MFT-style tops. Both styles earn a place because benches differ, and the right choice follows the holes already drilled in your top.

Narex Hot Forged Workbench Holdfast

Narex Hot Forged Workbench Holdfast

Narex Hot Forged Workbench Holdfast

Check price on Amazon

The Narex holdfast follows the centuries-old blacksmith pattern, hot forged from steel with a rough-finished shaft. That rough surface is functional rather than cosmetic: the listing describes shafts that grip the walls of the dog hole tightly, and the forged construction is built for repeated mallet work over years of use. Narex positions it for benches from 2 to 4 inches thick, and the published capacity covers boards up to 6 inches thick, which is generous headroom for aprons, thick workbench legs and stacked stock.

Because the shaft is a full 3/4 inch (19.05 mm), it suits standard 3/4 inch dog holes without the looseness that makes lighter holdfasts skate. The maker notes the tool is best used in pairs, which matches how most bench work goes: one holdfast near each end of a long board keeps it from pivoting under a plane. There is no pad in the box, so a scrap of leather or thin wood between the arm and the workpiece is the traditional workaround on finished surfaces. Sold singly, it sits in the premium tier, and woodworkers who want the forged pattern in a production tool rather than a one-off smith commission are the audience.

Specs

  • Shaft diameter: 3/4 inch (19.05 mm)
  • Dog hole size: 3/4 inch
  • Reach: not published as a separate figure in the listing specifications
  • Material: hot forged steel with a rough-finished, uncoated shaft
  • Pad included: no pad included
  • Pack count: 1 holdfast
  • Bench thickness range: 2 to 4 inches, per the maker
  • Workpiece capacity: boards up to 6 inches thick, per the maker

Pony Jorgensen 1708 Bench Hold-Down Clamp

The Pony bench hold-down clamp, model 1708, is the long-running American pattern in this group: a solid ductile iron body with a black baked-enamel finish, made by the Adjustable Clamp Company line that now sits under Pony Jorgensen. The maker catalog lists an 8 inch length and a 4 inch reach, the longest published reach among the traditional picks here, which helps when a board is wide or the nearest dog hole sits well back from the edge of the work.

One specification deserves attention. The maker catalog gives an 11/16 inch shaft and calls for an 11/16 inch predrilled hole, while the Amazon listing markets the pair for standard 3/4 inch dog holes. A traditional holdfast needs a small amount of play so the shaft can cant and lock, and the maker figure is the one to trust when you drill: this is the specs number, not the headline number. The clamps arrive as a pair, so a two-point hold on long stock is covered in one purchase. No pad is included, and the baked-enamel finish is there to protect the iron rather than the workpiece, so keep a leather scrap nearby for finished faces. In the mid-range tier, this is the pick for woodworkers who want a named maker with a published catalog behind the tool.

Specs

  • Shaft diameter: 11/16 inch, per the maker catalog
  • Dog hole size: 11/16 inch predrilled hole per the maker catalog; listing markets the pair for 3/4 inch dog holes
  • Reach: 4 inches
  • Length: 8 inches
  • Material: ductile iron with a black baked-enamel finish
  • Pad included: no pad included
  • Pack count: 2 clamps

POWERTEC 71528 8-Inch Workbench Holdfast

POWERTEC 71528 8-Inch Workbench Holdfast

POWERTEC 71528 8-Inch Workbench Holdfast

Check price on Amazon

The POWERTEC 71528 is the mainstream cast option: an 8 inch holdfast with a 3-1/2 inch reach, sold as a set of two for 3/4 inch bench dog holes. The listing describes a metal body with a powder coated grey color and a rough as-cast finish, and that texture matters for the same reason it does on the Narex: a holdfast holds by friction, and a smooth polished shaft is the enemy of a firm seat. The as-cast surface gives the hole wall something to bite.

The published routine is the classic one: drill or use an existing 3/4 inch hole, tap once or twice with a mallet to secure the work, and tap the backside of the vertical head to release. POWERTEC publishes model number 71528 and UPC 843441105671 for this set, which makes it easy to confirm you are looking at the right listing among the many similar cast holdfasts sold online. Reach of 3-1/2 inches covers most board widths when holes are spaced along the bench, and the pair format suits the two-point hold that keeps long stock from rotating. No pads are included. This set sits in the mid-range tier and is the default recommendation for a first pair of traditional holdfasts on a standard bench.

Specs

  • Shaft diameter: sized for 3/4 inch dog holes
  • Dog hole size: 3/4 inch
  • Reach: 3-1/2 inches
  • Length: 8 inches
  • Material: cast metal with a grey powder coated finish and rough as-cast surface
  • Pad included: no pads included
  • Pack count: 2 holdfasts
  • Model number: 71528

IMPRESA Holdfast Dog-Hole Clamps, Pack of 3

IMPRESA Holdfast Dog-Hole Clamps, Pack of 3

IMPRESA Holdfast Dog-Hole Clamps, Pack of 3

Check price on Amazon

The IMPRESA pack takes the same traditional pattern and bundles three holdfasts in one box, which is the practical difference in this lineup: three clamping points cover a panel glue-up station, a long board held at both ends with a third clamp in reserve, or two benches equipped at once. Each clamp is an 8 inch cast iron holdfast with a 3/4 inch shaft and a 3.5 inch shepherd hook reach, per the listing specifications.

The listing also notes a 1.3 inch square end design on the arm, a detail aimed at spreading contact on the workpiece. Cast iron is the traditional material for this pattern and the heaviest of the group per clamp, which helps the tool stay seated when a board shifts under planing pressure. The working method matches the other traditional picks: seat the shaft in a 3/4 inch dog hole, tap the top to lock, tap the back to release. No pads are listed in the box contents. As a three-pack of cast iron clamps, this is the budget tier route to covering a whole bench, and it suits woodworkers setting up a new bench who would rather buy clamping points in quantity than collect pairs over time.

Specs

  • Shaft diameter: 3/4 inch
  • Dog hole size: 3/4 inch
  • Reach: 3.5 inches
  • Length: 8 inches
  • Material: cast iron
  • Pad included: no pads listed
  • Pack count: 3 holdfasts
  • Arm end design: 1.3 inch square end, per the listing

RUIITEN 2 Pack MFT Bench Holdfast

The RUIITEN pair is the modern outlier in this group, built for the 20mm dog holes found in MFT-style multifunction tables rather than the 3/4 inch holes of a traditional bench. Each clamp is machined from aluminum alloy with stainless steel components, and instead of a mallet tap it uses a cam action with three pressure levels, high, medium and low, so clamping force can be matched to delicate veneered parts or rough stock with the same tool.

The listing, sold under part number EZ2022, describes the cam running parallel to the pressure plate for even pressure across the contact face, and the clamps holding tightly without walking out of the borehole. That integrated pressure plate also does the job a separate pad does on a traditional holdfast, spreading force on the workpiece surface. A 20mm clamp will not seat in a 3/4 inch hole, so this pick is strictly for MFT owners and woodworkers whose benches were drilled on the 20mm grid. Sold as a 2-pack in the budget tier, it is the natural companion to the track-saw table workflow, where work is carved, routed and sanded on the same perforated top.

Specs

  • Shaft diameter: post sized for 20mm dog holes
  • Dog hole size: 20mm
  • Reach: quick-acting cam design; no hook reach figure published
  • Material: aluminum alloy and stainless steel
  • Pad included: integrated pressure plate on each clamp
  • Pack count: 2 clamps
  • Pressure levels: 3 (high, medium, low), per the listing
  • Part number: EZ2022

How to Choose the Right Holdfast

Begin with the holes in your bench, because nothing else matters if the shaft does not fit. The long-standing standard for wooden workbenches is a 3/4 inch round dog hole, and four of the five picks here are built around it. MFT-style tops and some newer benches use a 20mm grid instead, which is where the RUIITEN cam clamps belong. A clamp made for one size will not seat correctly in the other, so measure a hole before ordering rather than assuming.

Reach comes next. Reach is the distance from the shaft to the tip of the arm, and it decides how far onto a board the clamp can press. The Pony publishes 4 inches, the POWERTEC and IMPRESA publish 3-1/2 inches, and wider work simply needs the hole row closer to the bench edge or a longer-reach tool. Bench thickness matters too: the Narex is published for tops from 2 to 4 inches thick, and a shaft needs enough engagement below the surface to cant and lock, so very thin tops are a poor match for any traditional holdfast.

Material and finish shape long-term behavior. Hot forged steel, as on the Narex, is the traditional premium route. Ductile iron on the Pony and cast iron on the IMPRESA give traditional patterns at lower tiers, while a rough or as-cast shaft surface is a feature on every traditional pick because friction is the whole mechanism. Finally, count the clamps. Boards pivot around a single holdfast, so pairs are the working minimum for long stock, and the three-pack exists for benches that need several clamping points at once. If your work involves finished surfaces, note which picks include any form of pad and plan on leather scraps for the ones that do not.

Frequently Asked Questions

What size dog hole does a holdfast need?

Most traditional holdfasts are built for 3/4 inch round dog holes, and four picks in this guide follow that standard. The exception is the RUIITEN cam clamp, which is made for 20mm holes in MFT-style tables. The Pony catalog specs an 11/16 inch shaft and hole, so check maker figures before drilling new holes.

How does a holdfast hold without a screw or lever?

The shaft drops loosely into the dog hole, and a mallet tap on top cants it so the shaft binds against the hole wall at two points while the arm presses the workpiece. Friction does the holding. A tap on the back of the arm straightens the shaft and releases the grip, which is why a rough shaft finish helps rather than hurts.

How many holdfasts should a bench have?

Two is the practical minimum for most work, since a single holdfast lets a long board pivot around the clamping point. Pairs cover the common cases, and a three-pack like the IMPRESA set adds a spare point for wide panels or a second work area. The Narex maker guidance also describes its holdfast as best used in pairs.

Will a holdfast mark the workpiece?

It can, because the arm bears directly on the wood and none of the traditional picks here include a pad. The long-standing fix is a scrap of leather or thin wood between the arm and the workpiece, which spreads the pressure and protects finished faces. The RUIITEN clamp takes a different route with an integrated pressure plate on each clamp.

Conclusion

The holdfast is one of the oldest workholding tools in the shop because the mechanism is simple and the published specifications tell you nearly everything before you buy. Match the shaft to your dog holes first: 3/4 inch for a traditional bench, 20mm for an MFT top. Then compare reach, material and pack count. The Narex is the premium forged choice, the Pony 1708 and POWERTEC 71528 pairs anchor the mid-range with maker-published dimensions, the IMPRESA three-pack covers a bench on a budget, and the RUIITEN cam clamps serve 20mm tables. Any of them will hold a board still while the real tools do the work.

F
FD Woodworking Editorial Team
We compare specs, warranty terms, long-term owner feedback and street pricing before anything earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Holdfasts for Workbench Woodworking: 5 Top PicksCheck price on Amazon

Related guides

Browse all Uncategorized guides →

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Business

A free business account with business pricing and bulk-buying tools for work, shop or home office.

Create a business account
Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.